< Back ×
My Vehicle Change Vehicle
2010 GMC Yukon
< Back to View All
Alignment Kits
- Department
- Prices
OEM (Genuine) 2010 GMC Yukon Motor Nut
PartNumber: 11516078
Product Specifications- Location: Driver Side; Passenger Side
- Item Dimensions: 1.6 x 1.5 x 0.7 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaces: 11518997, 11588927, 11508101
- Part Description: 2010 GMC Yukon Motor Nut
Vehicle Fitment- 2010 GMC Yukon | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
$4.54 MSRP:$7.20You Save: $2.66 (37%)
OEM (Genuine) 2010 GMC Yukon Alignment Cam
PartNumber: 15741217
Product Specifications- Notes: 2WD; 4WD
- Location: Driver Side; Passenger Side
- Other Names: Alignment Cam
- Item Dimensions: 3.3 x 2.4 x 0.3 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2010 GMC Yukon Alignment Cam
Vehicle Fitment- 2010 GMC Yukon | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
$4.54 MSRP:$7.17You Save: $2.63 (37%)
OEM (Genuine) 2010 GMC Yukon Cam Kit, Front Upper Control Arm Adjust
PartNumber: 12472859
Product Specifications- Notes: 2WD; 4WD
- Location: Driver Side; Passenger Side
- Other Names: Adjust Cam
- Item Dimensions: 6.1 x 5.8 x 3.3 inches
- Item Weight: 2.60 Pounds
- Part Description: 2010 GMC Yukon Cam Kit, Front Upper Control Arm Adjust
Vehicle Fitment- 2010 GMC Yukon | Denali, Denali Hybrid, Hybrid, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L ELECTRIC/FLEX, 8 Cyl 6.0 L ELECTRIC/GAS, 8 Cyl 6.0 L GAS
FAQ for Camber and Alignment Kit Repair
Q: What is the recommended torque for the jam nut on the tie rod?
A:
The recommended torque is 75 Nm (55 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the cam nuts?
A:
The recommended torque is 190 Nm (140 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What should I notice in Front Caster and Camber adjustment?
A:
Caster measurements are now relative to the ground. The caster and camber adjustments are made by rotating the offset cam bolt and the cam in the slotted frame bracket to reposition the control arm. Before adjusting the caster and camber angles, jounce the front bumper 3 times to allow the vehicle to return to normal height. Measure and adjust the caster and the camber with the vehicle at curb height. The front suspension Z dimension is indicated in Trim Heights.
By Bob
GM Specialist
01/11/2022Q: How to align Wheel-Steering Wheel Angle and/or Front Toe?
A:
You can loosen the jam nut on the inner tie rod, rotate the inner tie rod to the required toe specification setting, install the jam nut, check the toe setting after tightening, and re-adjust the toe setting if necessary.
By Bob
GM Specialist
01/11/2022Q: How to measure the front and rear alignment angles?
A:
You can install the alignment equipment according to the manufacturer's instructions, jounce the front and the rear bumpers 3 times before checking the wheel alignment, measure the alignment angles and record the readings, and adjust alignment angles to vehicle specification, if necessary.
By Bob
GM Specialist
01/11/2022