< Back ×
My Vehicle Change Vehicle
2009 Chevrolet Silverado 3500 HD
< Back to View All
Cameras & Driver Safety
- Department
- Brands
- Prices
OEM (Genuine) 2009 Chevrolet Silverado 3500 HD Reverse Sensor
PartNumber: 19115806
Product Specifications- Notes: In Bumper
- Other Names: Reverse Sensor
- Item Dimensions: 2.6 x 1.6 x 1.1 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaced by: 20908127
- Part Description: 2009 Chevrolet Silverado 3500 HD Reverse Sensor
Vehicle Fitment- 2009 Chevrolet Silverado 3500 HD | LT, LTZ, WT | 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
$216.25 MSRP:$326.25You Save: $110.00 (34%)
Dorman® Rear Parking Assist Sensor for 2009 Chevrolet Silverado 3500 HD
PartNumber: 684-060Product Specifications- Connector Gender: Male
- Mounting Hardware Included: No
- Package Contents: 1 Parking Aid Sensor
- Terminal Gender: Male
- Terminal Quantity: 3
- Terminal Type: Pin
- Universal Or Specific Fit: Specific
- UPC: 885484583979
- Wiring Harness Included: No
- Part Description: 2009 Chevrolet Silverado 3500 HD Rear Parking Assist Sensor
Vehicle Fitment- 2009 Chevrolet Silverado 3500 HD | All Trims | All Engines
$25.76OEM (Genuine) 2009 Chevrolet Silverado 3500 HD Reverse Sensor
PartNumber: 19115805
Product Specifications- Notes: Silverado, Sierra; In Step Pad
- Other Names: Reverse Sensor, Sensor
- Item Dimensions: 1.9 x 2.0 x 1.4 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaced by: 25844782
- Part Description: 2009 Chevrolet Silverado 3500 HD Reverse Sensor
Vehicle Fitment- 2009 Chevrolet Silverado 3500 HD | LT, LTZ, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
FAQ for Parking Sensors Repair
Q: How to remove the Rear Object Sensor?
A:
You should disconnect the electrical from the rear object sensor and then lift the locking tabs on the housing and remove the rear object sensor.
By Bob
GM Specialist
02/11/2022Q: How to replace the Rear Object Sensor Housing?
A:
You should remove the center rear bumper step pad or the rear bumper impact bar end cap, remove the sensor from the sensor housing, apply structural adhesive epoxy, install the sensor housing to the fascia, and allow the adhesive to cure according to the manufacturer's directions, install the sensor to the sensor housing, connect the electrical harness and then install the center rear bumper step pad or the rear bumper impact bar end cap.
By Bob
GM Specialist
02/11/2022Q: How to install the Rear Object Sensor?
A:
You should paint the rear object sensor, ensure the paint does not exceed 6 mils, insert the sensor into the housing and then connect the electrical connector to the rear object sensor.
By Bob
GM Specialist
02/11/2022Q: How to service the Rear Object Sensor Housing?
A:
You should remove the rear object sensor and then release the 2 tabs behind the housing to remove.
By Bob
GM Specialist
02/11/2022Q: How to service the Rear Object Alarm Module Assembly?
A:
You should place a carpet to access the module, disconnect the electrical connector and then replace the module after replacement.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the Information Center Telltale screws?
A:
The recommended torque is 2 N.m (18 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the rear object alarm module nuts?
A:
The recommended torque is 9 N.m (80 lb in).
By Bob
GM Specialist
01/11/2022Q: How many nuts attach to the Rear Object Alarm Module?
A:
There are 3 nuts attaching the Rear Object Alarm Module.
By Bob
GM Specialist
01/11/2022Q: How many screws attach to the Information Center Telltale?
A:
There are 2 screws attaching the Information Center Telltale.
By Bob
GM Specialist
01/11/2022See more FAQs (4)