< Back ×
My Vehicle Change Vehicle
2009 Chevrolet Silverado 2500 HD
< Back to View All
Alignment Kits
- Department
- Prices
OEM (Genuine) 2009 Chevrolet Silverado 2500 HD U-Bolt Nut
PartNumber: 11516382
Product Specifications- Notes: Chevrolet, 3/4 & 1 Ton
- Location: Driver Side; Passenger Side
- Item Dimensions: 4.2 x 3.0 x 0.7 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 22123946, 15702050, 15048124, 14013439
- Part Description: 2009 Chevrolet Silverado 2500 HD U-Bolt Nut
Vehicle Fitment- 2009 Chevrolet Silverado 2500 HD | High Country, LT, LTZ, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
$1.14 MSRP:$1.79You Save: $0.65 (37%)
OEM (Genuine) 2009 Chevrolet Silverado 2500 HD Cam Kit, Front Upper Control Arm Adjust
PartNumber: 12472859
Product Specifications- Notes: 2WD, 3/4 & 1 Ton; 4WD, 3/4 & 1 Ton
- Location: Driver Side; Passenger Side
- Other Names: Adjust Cam
- Item Dimensions: 6.1 x 5.8 x 3.3 inches
- Item Weight: 2.60 Pounds
- Part Description: 2009 Chevrolet Silverado 2500 HD Cam Kit, Front Upper Control Arm Adjust
Vehicle Fitment- 2009 Chevrolet Silverado 2500 HD | Base, LS, LT, LTZ, WT | 8 Cyl 6.0 L BI-FUEL, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
FAQ for Camber and Alignment Kit Repair
Q: What may cause steering and vibration complaints?
A:
Steering and vibration complaints may be the result of improper alignment, wheel, and tire imbalance, and tire lead due to worn or improperly manufactured tires.
By Bob
GM Specialist
01/11/2022Q: What steps should you perform to measure the front and rear alignment angles?
A:
You should install the alignment equipment, jounce the front and the rear bumpers 3 times, measure the alignment angles, record the readings and adjust alignment angles to vehicle specification.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque when you install the jam nut?
A:
You can tighten the nut to 75 Nm (55 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How do you adjust the front caster and camber?
A:
You can rotate the offset cam bolt and the cam in the slotted frame bracket, determine the caster angle, determine the positive camber or negative camber angle, remove the pinned adjusting cam insert, loosen the upper control arm cam adjustment bolts, adjust the caster and the camber angle and verify that the caster and the camber are still within specifications.
By Bob
GM Specialist
01/11/2022Q: How do you adjust the Wheel Alignment-Steering Wheel Angle and/or Front Toe?
A:
You can loosen the jam nut on the inner tie rod, rotate the inner tie rod to the required toe specification setting, install the jam nut on the tie rod, check the toe setting, and re-adjust the toe setting.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque when you tighten the cam nuts?
A:
You can tighten the cam nuts to 190 Nm (140 lb-ft).
By Bob
GM Specialist
01/11/2022See more FAQs (1)