Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2009 Chevrolet Avalanche Parking Sensors

2009 Chevrolet Avalanche Parking Sensors

My Vehicle Change Vehicle
2009 Chevrolet Avalanche
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Cameras & Driver Safety
  • Department
  • Prices

1 Product found

4 Q&A for Parking Sensors Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2009 Chevrolet Avalanche Reverse Sensor Diagram - 15239247
    View Related Parts

    OEM (Genuine) 2009 Chevrolet Avalanche Reverse Sensor

    PartNumber: 15239247
    OEM 2009 Chevrolet Avalanche Reverse Sensor - 15239247
    Product Specifications
    • Notes: Reverse Sensing System; Avalanche, Escalade Ext
    • Other Names: Alarm, Park Sensor, Reverse Sensor, Sensor
    • Item Dimensions: 4.8 x 2.3 x 1.9 inches
    • Item Weight: 0.30 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 19116085
    • Part Description: 2009 Chevrolet Avalanche Reverse Sensor
    More Info
    Vehicle Fitment
    • 2009 Chevrolet Avalanche | Black Diamond LS, Black Diamond LT, Black Diamond LTZ, LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    $159.65 MSRP: $251.08
    You Save: $91.43 (37%)

FAQ for Parking Sensors Repair

Q: How do you remove the rear object sensor?
A:
You can remove the rear bumper fascia, disconnect the electrical connector, and remove the rear object sensor.
By Bob
GM Specialist
02/11/2022
Q: What is the rear object sensor housing replacement procedure?
A:
First, remove the rear fascia and disconnect the sensor harness. Remove the sensor from the sensor housing and sand/grind sonic weld plastic residue from the fascia. Next, apply structural adhesive epoxy, install the sensor housing to the fascia and allow the adhesive to cure. Finally install the sensor to the sensor housing, connect the electrical harness and install the rear fascia.
By Bob
GM Specialist
02/11/2022
Q: How many nuts does the rear object alarm module have?
A:
The rear object alarm module has a total of 3 nuts.
By Bob
GM Specialist
01/11/2022
Q: What is the information center telltale assembly service procedure?
A:
Disconnect the electrical connectors and tighten the information center telltale screws to 2 Nm.
By Bob
GM Specialist
01/11/2022

FAQ for Other Repair Info

Q: What is the starter installation procedure?
A:
First, install the Starter heat shield, snap the transmission cover onto the starter and install the starter through the wheel well opening. Next install the started solenoid cable to the starter, install the starter solenoid cable nut and tighten the nut to 9 Nm. Place the starter solenoid cable clip into the frame, install the starter solenoid cable clip bolt and tighten the clip bolt to 10 Nm. Install the engine wiring harness lead terminal to the starter, install the engine wiring harness lead nut and tighten to 3.4 Nm. After that install the starter bolts and tighten the bolts to 50 Nm.
Q: What is the body control module service procedure?
A:
Remove the knee bolster, and the BCM cover and disconnect the electrical connector. Next press on the tabs to release the Body Control Module.
Q: What is the sunroof motor/actuator service procedure?
A:
Remove the overhead console and the sunroof module bracket. Make sure to tighten the Sunroof Motor/actuator screws to 6 Nm.