< Back ×
My Vehicle Change Vehicle
2008 Cadillac XLR
< Back to View All
Driveline, Axles & 4WD
- Department
- Prices
OEM (Genuine) 2008 Cadillac XLR Ring & Pinion
PartNumber: 19133225
Product Specifications- Notes: Xlr; 4.6l
- Other Names: Ring Pinion
- Item Dimensions: 10.6 x 9.8 x 8.9 inches
- Item Weight: 14.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Cadillac XLR Ring & Pinion
Vehicle Fitment- 2008 Cadillac XLR | Base, Platinum | 8 Cyl 4.6 L GAS
$785.17 MSRP:$1058.19You Save: $273.02 (26%)OEM (Genuine) 2008 Cadillac XLR Gear Set, Differential Ring & Drive Pinion
PartNumber: 19133224Product Specifications- Notes: Xlr; 4.4l
- Other Names: Ring Pinion
- Item Dimensions: 15.6 x 10.4 x 6.5 inches
- Fitment Type: Direct Replacement
- Replaces: 89059667
- Part Description: 2008 Cadillac XLR Gear Set, Differential Ring & Drive Pinion
Vehicle Fitment- 2008 Cadillac XLR | V | 8 Cyl 4.4 L GAS
FAQ for Ring And Pinion Repair
Q: What kind of special tools will be required in the assembly of the Ring Gear and Differential Housing?
A:
The tools required include J 42162 Getrag axle side gear compressor and the J 42170 Getrag axle bearing race installer.
By Bob
GM Specialist
01/11/2022Q: How to assemble the Drive Pinion?
A:
You should install the bearing onto the pinion shaft, the bearing onto the pinion shaft, and the nut onto the pinion shaft.
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required in the selection of the Drive Pinion Shim?
A:
The tools required include J 42168-1 shim measuring tool, J 42168-2 shim measuring tool, J 42168-9 shim measuring tool, J 42168-11 shim measuring tool, and J-42173-A differential holding fixture.
By Bob
GM Specialist
01/11/2022Q: How to assemble the Ring Gear and Differential Housing?
A:
You should install the right clutch pack to the right case, the right output shaft and gear, side gears, and washers to the right differential case, the gear to the left intermediate shaft, the C-clip to the left intermediate shaft, the left side bearing to the differential, the left clutch pack to the left case, the left intermediate shaft and gear to the left case, the case bolts and the right side bearing to the differential.
By Bob
GM Specialist
01/11/2022Q: What should be noted in the selection of the Drive Pinion Shim?
A:
You should make sure that all of the pinion housing/cage bolts must be installed to obtain an accurate measurement and correct shim selection.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the nut onto the pinion shaft?
A:
The recommended torque is 500 N.m (370 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required in the disassembly of the Drive Pinion?
A:
The tools required include DT-48005 pinion bearing remover, DT-48007 spline holder, J 42162 Getrag axle side gear compressor, and J 42172 Getrag axle bearing race installer.
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required in the disassembly of the Ring Gear and Differential Housing?
A:
The tools required include J-42159-A differential side bearing remover, J 42162 Getrag axle side gear compressor, and J-42173-A differential holding fixture.
By Bob
GM Specialist
01/11/2022Q: How to disassemble the Drive Pinion?
A:
You should remove the pinion nut using the J 42172 and the DT-48007 in a vise, the pinion shaft and bearing from the housing/cage, the nut, bearing, spacer, and pinion shaft from the housing/cage, install the DT-48005 onto the pinion shaft and bearing and remove the bearing from the shaft.
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be required in the assembly of the Drive Pinion?
A:
The tools required include a DT-48007 spline holder, J 42170 Getrag axle bearing race installer, and J 42172 Getrag axle bearing race installer.
By Bob
GM Specialist
01/11/2022See more FAQs (6)