< Back ×
My Vehicle Change Vehicle
2008 Cadillac SRX
< Back to View All
Rocker Panels & Floors
- Department
- Prices
OEM (Genuine) 2008 Cadillac SRX Panel Asm, Rear Compartment (Rear Half Only, Less Rails)
PartNumber: 89022238
Product Specifications- Other Names: Rear Floor Pan
- Item Dimensions: 61.3 x 37.7 x 8.2 inches
- Item Weight: 19.30 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Cadillac SRX Panel Asm, Rear Compartment (Rear Half Only, Less Rails)
Vehicle Fitment- 2008 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
FAQ for Floor Pan Repair
Q: How to remove the Rear Carpet Retainer?
A:
You should use a J 38778 to release the retainer clips from the rocker panel, tilt the carpet retainer inward and pull downward to release the trim from the retainer at the rear of the carpet retainer and remove the rear carpet retainer.
By Bob
GM Specialist
29/10/2022Q: How to install the Front Carpet Retainer?
A:
You should position the front upper retainer to the holes in the hinge pillar, align the front carpet retainer with the slots in the rocker panel and apply pressure along the entire length of the molding.
By Bob
GM Specialist
29/10/2022Q: How to eliminate unwanted odors in vehicles?
A:
You should spray GM vehicle care odor eliminator directly or as an additive with carpet shampoo in steam cleaners, avoid using it on any interior surface that plain water would deteriorate because this product will have the same effect, and avoid letting this product come into contact with vinegar or any acidic substance, complete eight-page treatment sheets are enclosed within each case of vehicle care odor eliminator. These treatment instructions range from simple vehicle odor elimination to full step-by-step procedures for odor removal from water leaks and instructions and cautions are printed on the bottle, but additional help is available.
By Bob
GM Specialist
29/10/2022Q: How to remove the Front Floor Panel Carpet?
A:
You should remove the appropriate front seat, the center console, the front carpet retainer, the rear carpet retainer, the center pillar garnish molding, and the carpet.
By Bob
GM Specialist
29/10/2022Q: How to install the Rear Carpet Retainer?
A:
You should position the rear carpet retainer with the slots in the rocker, tilt the trim plate to align the retainer at the rear of the carpet retainer, position the retainers into the slots on the rocker panel and press downward to engage the retainers into the slots in the rocker panel.
By Bob
GM Specialist
29/10/2022Q: How to dry the Floor Carpet?
A:
For a 1-piece carpet assembly bonded to cotton or fiber padding, you should replace the entire assembly. For a 2-piece carpet assembly with cotton or fiber padding, you should replace the padding only. For a 1-piece carpet assembly bonded to foam padding or attached to synthetic padding or a 2-piece carpet assembly with synthetic padding, you should observe puddles of liquid on the carpet face, use a wet vacuum to remove the excess moisture, blot the face of the carpet with a towel to absorb as much moisture as possible and point a fan at the affected area and air dry the carpet.
By Bob
GM Specialist
29/10/2022Q: How to remove the Front Carpet Retainer?
A:
You should use a J 38778 to release the retainer clips from the rocker panel, slide the carpet retainer rearward and remove the front carpet retainer.
By Bob
GM Specialist
29/10/2022Q: How to remove the Rear Floor Panel Carpet?
A:
To prevent SIR deployment, personal injury, or unnecessary SIR system repairs, you should not strike the door or the door pillar in the area of the side impact sensor (SIS). Then, you should turn off the ignition and remove the key when performing service in the area of the SIS, remove the rear seats, the rear carpet retainers, the rear sill plate, the body side rear trim panels, and the rear carpet from the vehicle.
By Bob
GM Specialist
29/10/2022Q: How to install the Front Floor Panel Carpet?
A:
You should position the front floor carpet into place over the front edge of the rear carpet, make sure the electrical connector is carefully positioned under the front carpet piece, align the carpet to the dash panel, the rocker panel, the tunnel, and the seat attachment areas, tuck the carpet behind the tab on the HVAC duct, ensure all wrinkles are removed and install the center console, the center pillar garnish molding, the front carpet retainer, the rear carpet retainer, and the front seat.
By Bob
GM Specialist
29/10/2022Q: How to remove the Intermediate Carpet?
A:
You should remove the front seats, the center console, the rear seat, the front carpet retainers, the rear carpet retainers, and the center pillar garnish moldings, disconnect the push-in retainers at the rear ducts, lift the rear carpet to disengage the front floor ducts from the rear floor duct assembly, remove the intermediate carpet from the vehicle, disconnect the push-in retainers from the air ducts to carpet and remove the air ducts from the carpeting.
By Bob
GM Specialist
29/10/2022See more FAQs (5)