Notes: OE Recommended Replacement filter; Premium activated charcoal media; Removes odors in addition to capturing pollen, dust, & other allergens
Filter Media Material: CHARCOAL
Height: 0.9
Length: 9.1
Reusable: No
UPC: 042511091115
Width: 10.44
Part Description: 2008 Cadillac SRX Cabin Air Filter
More Info
Vehicle Fitment
2008 Cadillac SRX | All Trims | 6 Cyl 3.6L
2008 Cadillac SRX | All Trims | 8 Cyl 4.6L
FAQ for Cabin Air Filter Repair
Q: How to install the Passenger Compartment Air Filter Housing (Left Hand Drive)?
A:
You should install the filter into the filter housing, the filter access cover, and the air inlet grille access panel.
By Bob
GM Specialist
29/10/2022
Q: How to remove the Passenger Compartment Air Filter Housing (Left Hand Drive)?
A:
You should remove the air inlet grille access panel, release the tabs on each side of the access cover, lift up and remove the filter access cover and remove the filter from the filter housing.
By Bob
GM Specialist
29/10/2022
Q: How to remove the Passenger Compartment Air Filter Housing (Right Hand Drive)?
A:
You should remove the air inlet grille access panel, release the tabs on each side of the access cover, lift up and remove the filter access cover and remove the filter from the filter housing.
By Bob
GM Specialist
29/10/2022
Q: How to remove the Passenger Compartment Air Filter (Left Hand Drive)?
A:
You should remove the air inlet grille panel, release the tabs on each side of the access cover, lift up and remove the filter access cover, remove the filter from the filter housing, gently pry out on the filter housing to separate the housing from the sheet metal and remove the passenger air filter housing.
By Bob
GM Specialist
29/10/2022
Q: How to install the Passenger Compartment Air Filter (Left Hand Drive)?
A:
You should install the passenger air filter housing, press the passenger air filter housing until all clips engage into the sheet metal, ensure that there is a good seal between the passenger air filter housing and the sheet metal and install the filter into the filter housing, the filter access cover and the air inlet grille panel.
By Bob
GM Specialist
29/10/2022
Q: How to remove the Passenger Compartment Air Filter (Right Hand Drive)?
A:
You should remove the air inlet grille panel, release the tabs on each side of the access cover, lift up and remove the filter access cover, remove the filter from the filter housing, gently pry out on the filter housing to separate the housing from the sheet metal and remove the passenger air filter housing.
By Bob
GM Specialist
29/10/2022
Q: How to install the Passenger Compartment Air Filter (Right Hand Drive)?
A:
You should install the passenger air filter housing, press the passenger air filter housing until all clips engage into the sheet metal, ensure that there is a good seal between the passenger air filter housing and the sheet metal and install the filter into the filter housing, the filter access cover and the air inlet grille panel.
By Bob
GM Specialist
29/10/2022
Q: How to install the Passenger Compartment Air Filter Housing (Right Hand Drive)?
A:
You should install the filter into the filter housing, the filter access cover, and the air inlet grille access panel.
By Bob
GM Specialist
29/10/2022
See more FAQs (3)
FAQ for Other Repair Info
Q: How to install the Auxiliary Blower Motor?
A:
You should install the Blower Motor to the HVAC module and the blower motor screws, tighten the screws, connect the blower motor electrical connector and install the left body side trim access panel.
Q: How to remove the Heater Core?
A:
You should remove the HVAC module, the Heater Core pipe bracket screw, the heater core pipe bracket, and the heater core from the HVAC module.
Q: How to remove the Heater Inlet Hose (LY7-Gas, 6 Cylinder, 3.6L, SFI, V6)?
A:
You should drain the cooling system, remove the battery tray, the cowl panel retaining bolts, and the cowl panel, use J 38185 to slide the clamp away from the base of the heater inlet hose, remove the inlet Heater Hose from the heater core, use J 38185 slide the clamp away from the base of the heater inlet hose and remove the clamp and hose from the engine cooling thermostat assembly.