Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
Replacement and OEM Parts for 2008 Cadillac DTS Parking Sensors

2008 Cadillac DTS Parking Sensors

My Vehicle Change Vehicle
2008 Cadillac DTS
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Cameras & Driver Safety
  • Department
  • Prices

2 Products found

10 Q&A for Parking Sensors Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM (Genuine) 2008 Cadillac DTS Reverse Sensor

    PartNumber: 15239247
    OEM 2008 Cadillac DTS Reverse Sensor - 15239247
    Product Specifications
    • Notes: Dts; Front Object;Dts; Rear Object
    • Other Names: Alarm, Park Sensor, Reverse Sensor, Sensor
    • Item Dimensions: 4.8 x 2.3 x 1.9 inches
    • Item Weight: 0.30 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 19116085
    • Part Description: 2008 Cadillac DTS Reverse Sensor
    More Info
    Vehicle Fitment
    • 2008 Cadillac DTS | Base, Luxury, Platinum | 8 Cyl 4.6 L GAS
    $159.65 MSRP: $251.08
    You Save: $91.43 (37%)
  • OEM (Genuine) 2008 Cadillac DTS Object Sensor

    PartNumber: 20823460
    OEM 2008 Cadillac DTS Object Sensor - 20823460
    Product Specifications
    • Notes: Blind Spot Monitoring; Dts
    • Location: Driver Side; Passenger Side
    • Other Names: Module, Object Sensor, Sensor
    • Item Dimensions: 5.6 x 4.6 x 1.4 inches
    • Item Weight: 1.00 Pounds
    • Fitment Type: Direct Replacement
    • Replaces: 1999430, 25978649, 25910830, 20759899, 01999430
    • Part Description: 2008 Cadillac DTS Object Sensor
    More Info
    Vehicle Fitment
    • 2008 Cadillac DTS | Base, Livery, Luxury, Platinum, Premium | 8 Cyl 4.6 L GAS
    $422.21 MSRP: $636.96
    You Save: $214.75 (34%)

FAQ for Parking Sensors Repair

Q: Can I grind off alignment tabs?
A:
No, you cannot.
By Bob
GM Specialist
02/11/2022
Q: How to remove the Rear Object Sensor Housing?
A:
You will need to remove the rear fascia, disconnect the sensor harness, remove the sensor from the sensor housing, sand/grind sonic weld plastic residue from the fascia, then apply structural adhesive epoxy, Lord Fusor(TM) 127EZ or equivalent to fascia at the mating surface, install the sensor housing to the fascia using the alignment tabs, next allow adhesive to cure according to manufacturer's directions, install the sensor to the sensor housing, connect the electrical harness and install the rear fascia.
By Bob
GM Specialist
02/11/2022
Q: How to install the Rear Object Sensor?
A:
You may need to insert the sensor into the housing, connect the electrical connector to the rear object sensor, and install the rear bumper fascia.
By Bob
GM Specialist
02/11/2022
Q: How to remove the Rear Object Sensor?
A:
You will need to remove the rear bumper fascia, disconnect the electrical from the rear object sensor, lift the locking tabs on the housing and remove the rear object sensor.
By Bob
GM Specialist
02/11/2022
Q: How to remove the Information Center Telltale Assembly?
A:
You will need to insert your fingers between the headliner and the information center telltale assembly bezel, then gently pull down to release the display bezel, next use a screwdriver to release the locking tab at the rear of the telltale assembly, then tilt the display down, pull down to remove, and disconnect the electrical connector.
By Bob
GM Specialist
01/11/2022
Q: What's the tip for replacing the Front and Rear Object Alarm Modules?
A:
You may disconnect electrical connectors.
By Bob
GM Specialist
01/11/2022
Q: How to install the Front Object Alarm Sensor?
A:
You may need to insert the sensor into the housing, connect the electrical connector to the front object sensor and install the front bumper fascia.
By Bob
GM Specialist
01/11/2022
Q: How to install the Information Center Telltale Assembly?
A:
You may need to connect the electrical connector to the information center telltale assembly, insert the display into the headliner until the locking tab locks into position, then install the bezel by pushing it up until the tabs lock into position.
By Bob
GM Specialist
01/11/2022
Q: How to remove the Front Object Alarm Sensor?
A:
You will need to remove the front bumper fascia, disconnect the electrical from the front object sensor, then lift the locking tabs on the housing and remove the front object sensor.
By Bob
GM Specialist
01/11/2022
Q: What's the preliminary procedure for replacing the Front and Rear Object Alarm Modules?
A:
The procedure is to remove the right side trim panel.
By Bob
GM Specialist
01/11/2022
See more FAQs (5)