< Back ×
My Vehicle Change Vehicle
2008 Cadillac CTS
< Back to View All
Fuel Systems
- Department
- Prices
OEM (Genuine) 2008 Cadillac CTS Injector
PartNumber: 12609418
Product Specifications- Notes: Cts; 3.6l
- Other Names: Injector
- Item Dimensions: 4.3 x 2.6 x 2.7 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: Injector
$48.64 MSRP:$91.80You Save: $43.16 (48%)
FAQ for Fuel Injector Repair
Q: How to remove the Fuel Injector Sight Shield (LLT)?
A:
First, you need to remove the cross-car brace and the oil fill cap. Then, please disengage the cover/shield from the ball studs and pull the engine cover/sight shield forward to remove it from the rear tabs. Finally, you should remove the engine cover/sight shield and the front compartment sight shield.
By Bob
GM Specialist
01/11/2022Q: How to remove the Fuel Injector Sight Shield(LP1, LY7)?
A:
First, you need to remove the cross-car brace and the oil fill cap. Then, please disengage the cover/shield from the ball studs by pulling up firmly on the right rear and left front of the engine cover. Finally, you should remove the engine cover/sight shield and the front compartment sight shield.
By Bob
GM Specialist
01/11/2022Q: How to install the Fuel Injector (LLT)?
A:
First, you need to install the upper O-ring Seal, the plastic Spacer, the retaining Ring, the isolator cup, and the Teflon Seal to the fuel injectors. Then, please install the direct fuel injectors to the cylinder head and install the NEW direct fuel injector hold-down clamps. Finally, you should connect the fuel injector wiring harness electrical connectors to the fuel injectors and install the fuel injection fuel rail assembly.
By Bob
GM Specialist
01/11/2022Q: How to install the Fuel Injector Sight Shield(LP1, LY7)?
A:
First, you need to install the front compartment sight shield and position the engine cover/sight shield over the intake manifold so the grommets are aligned with the ball studs. Then, please press the engine cover/sight shield down firmly near the ball studs to install the engine cover/sight shield. Finally, you should install the oil fill cap and the cross-car brace.
By Bob
GM Specialist
01/11/2022Q: How to install the Fuel Injector Sight Shield (LLT)?
A:
First, you need to install the front compartment sight shield and position the engine cover/sight shield to the rear tabs. Then, please position the engine cover/sight shield over the intake manifold so the grommets are aligned with the ball studs and press the engine cover/sight shield down firmly near the ball studs to install the engine cover/sight shield. Finally, you should install the oil fill cap and the cross-car brace.
By Bob
GM Specialist
01/11/2022Q: How to remove the Fuel Injector (LLT)?
A:
First, you need to relieve the high side fuel system pressure, remove the fuel injection fuel rail assembly and remove and discard the fuel injector hold-down clamp. Then, please disconnect the fuel injector wiring harness electrical connectors from the fuel injectors. Finally, you should remove the direct fuel injectors, remove and discard the upper O-ring Seal, the plastic Spacer, the retaining Ring, the isolator Cup, and the Teflon Seal from the fuel injectors.
By Bob
GM Specialist
01/11/2022Q: How to install the Fuel Injector and Fuel Rail (LP1, LY7)?
A:
First, you need to install NEW fuel injector seals, the fuel injector, the fuel injector retainer clip, and the fuel injector electrical connector. Then, please engage the fuel injector electrical connector lock, install the fuel rail with the fuel injectors and install the fuel rail bolts. Finally, you should connect the fuel feed pipe to the fuel rail, and install the fuel pipe retaining clip and the upper intake manifold.
By Bob
GM Specialist
01/11/2022Q: How to remove the Fuel Injector and Fuel Rail (LP1, LY7)?
A:
First, you need to relieve the fuel system pressure, remove the upper intake manifold with the lower intake manifold, remove the fuel pipe retaining clip and disconnect the fuel feed pipe from the fuel injector rail. Then, please use compressed air to remove debris from the area where the fuel injectors enter the intake manifold. You also need to remove the fuel rail bolts, remove the fuel rail with the fuel injectors, disengage the fuel injector electrical connector lock, and disconnect the fuel injector electrical connector. Finally, you should remove the fuel injector retainer clip, and the fuel injector, and remove and discard the fuel injector seals.
By Bob
GM Specialist
01/11/2022See more FAQs (3)