Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2008 Buick Enclave Drive Belt

2008 Buick Enclave Drive Belt

My Vehicle Change Vehicle
2008 Buick Enclave
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Timing Belts, Chains, Cams & Related Parts
  • Department
  • Prices

1 Product found

3 Q&A for Drive Belt Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2008 Buick Enclave Serpentine Belt Diagram - 12608660
    View Related Parts

    OEM (Genuine) 2008 Buick Enclave Serpentine Belt

    PartNumber: 12608660
    OEM 2008 Buick Enclave Serpentine Belt - 12608660
    Product Specifications
    • Other Names: Serpentine Belt
    • Item Dimensions: 21.5 x 5.8 x 1.0 inches
    • Item Weight: 0.70 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2008 Buick Enclave Serpentine Belt
    More Info
    Vehicle Fitment
    • 2008 Buick Enclave | Base, CX, CXL | 6 Cyl 3.6 L GAS
    $37.88 MSRP: $68.61
    You Save: $30.73 (45%)

FAQ for Drive Belt Repair

Q: What may be the cause of intermittent stiff steering, intermittent steering effort hard, intermittent compressor noise when AC is on, and intermittent drive belt squeal/chirp?
A:
It may be caused by water splashing onto the drive belt and causing the belt to slip on the pulleys.
By Bob
GM Specialist
29/10/2022
Q: What will need to be done before replacing the Drive Belt?
A:
You will need to raise the vehicle, rotate the drive belt tensioner clockwise to release the drive belt tension, slide the drive belt off of the belt idler pulley, and then slowly release the drive belt tensioner.
By Bob
GM Specialist
29/10/2022
Q: How do you correct these conditions?
A:
You should inspect the right front inner wheel well for a splash shield, and replace both front inner wheel well front liners with a second design (see part numbers below) if the vehicle does not have the splash shield as seen above, drill two 8 mm (0.315 in) holes into the cradle to attach the lower splash shield to the cradle, use the lower splash shield as a template to show where to drill the holes, get two retainers, P/N 21030249 or equivalent, to attach the lower splash shield to the cradle, drill holes in the cradle for the retainers, and then apply an anti-corrosion material to the holes.
By Bob
GM Specialist
29/10/2022

FAQ for Other Repair Info

Q: How do you install the Primary Camshaft Drive Chain and Sprockets?
A:
You need to ensure the crankshaft sprocket is installed with the timing mark visible, install the crankshaft sprocket onto the nose of the crankshaft, align the notch in the crankshaft sprocket with the pin in the crankshaft, slide the crankshaft sprocket on the crankshaft nose until the crankshaft sprocket contacts the step in the crankshaft, ensure the crankshaft is in the stage one timing position with the crankshaft sprocket timing mark aligned to the stage one timing mark on the oil pump cover, and then install the primary camshaft Timing Chain, the primary upper camshaft drive chain guide, the primary camshaft drive chain tensioner, the right bank secondary camshaft drive chain, the right bank secondary camshaft drive chain guide, the right bank secondary camshaft drive chain shoe, the right bank secondary camshaft drive chain tensioner, the spark plugs, and the engine front cover.
Q: What will need to be done for preventing camshaft/engine rotation?
A:
You will need to use an open-end wrench at the Camshaft hex.
Q: What is the recommended torque for the engine front cover bolts?
A:
The recommended torque is 23 N.m (17 lb-ft).