< Back ×
My Vehicle Change Vehicle
2005 Buick LeSabre
< Back to View All
Air Filters & Intake Systems
- Department
- Prices
OEM (Genuine) 2005 Buick LeSabre Throttle Body Assembly
PartNumber: 24507226
Product Specifications- Notes: Bonneville, Lesabre; W/O Supercharger; 3.8l
- Other Names: Throttle Body
- Item Dimensions: 8.2 x 8.1 x 7.4 inches
- Item Weight: 3.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2005 Buick LeSabre Throttle Body Assembly
Vehicle Fitment- 2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
FAQ for Throttle Body Repair
Q: How to install the Accelerator Controls Cable?
A:
You should install the accelerator control cable through the bulkhead, install the snap retainer through the bulkhead, install the accelerator control cable through the slot in the accelerator pedal lever, assemble the dash panel insulator retainer to the accelerator control cable, push (from the passenger compartment) the retainer over cable lever end fitting and up cable until the retainer snaps onto the flange of cable dash fitting, check for complete throttle opening and closing positions by operating the accelerator pedal, install the accelerator control cable to the throttle body lever, install the accelerator control cable to the accelerator cable bracket, install the accelerator control cable to the right slot on top of washer bottle, install the accelerator control cable to the retaining clip and install the left closeout/insulator panel.
By Bob
GM Specialist
02/11/2022Q: How to remove the Accelerator Controls Cable Bracket?
A:
You should remove the fuel injector sight shield, disconnect the cruise control cable from the throttle lever, disconnect the cruise control cable from the bracket, disconnect the accelerator cable from the throttle lever, disconnect the accelerator cable from the bracket, remove the wiring harness clip from a bracket if necessary (VIN K only) and remove the two bolts from the bracket.
By Bob
GM Specialist
02/11/2022Q: How to install the Throttle Body Air Inlet Screen?
A:
You should install the throttle body air inlet screen into the throttle body, install the snap ring onto the throttle body and install the air cleaner intake duct.
By Bob
GM Specialist
02/11/2022Q: What should be noticed in installing the Throttle Body Assembly?
A:
The throttle should operate freely without binding between fully closed and wide open throttle (WOT).
By Bob
GM Specialist
02/11/2022Q: How to clean the Throttle Body?
A:
You should remove the air cleaner intake duct, remove the air inlet screen, if applicable, inspect the throttle body bore and the throttle valve plate for deposits and clean the throttle body bore and the throttle valve plate using a clean shop towel. If the deposits are excessive, you should remove and disassemble the throttle body for cleaning. After disassembly, you should clean the throttle body using a parts-cleaning brush. If you removed and disassembled the throttle body for cleaning, you should assemble and install the throttle body. Then you should install the air inlet screen and install the air cleaner intake duct.
By Bob
GM Specialist
02/11/2022Q: What should be noticed when removing the Throttle Body Assembly?
A:
You cannot use solvent of any type when cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as damage to the gasket surfaces and throttle body assembly may result. You should use care in cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as sharp tools may damage the gasket surfaces.
By Bob
GM Specialist
02/11/2022Q: How to remove the Accelerator Controls Cable?
A:
You should remove the left closeout/insulator panel, remove the accelerator control cable from the accelerator pedal lever, squeeze the accelerator cable cover tangs and push the accelerator cable through the bulkhead, remove the accelerator control cable from the retaining clip, remove the accelerator control cable from the right slot on top of washer bottle, remove the accelerator cable from the throttle body lever, and remove the accelerator cable from the accelerator control cable bracket.
By Bob
GM Specialist
02/11/2022Q: How to remove the Throttle Body Air Inlet Screen?
A:
You should remove the air cleaner intake duct, remove the snap ring from the throttle body and remove the throttle body air inlet screen from the throttle body.
By Bob
GM Specialist
02/11/2022Q: How to install the Accelerator Controls Cable Bracket?
A:
You should install the two brackets bolts, install the wiring harness clip from the bracket if necessary, install the accelerator cable to the bracket, install the accelerator cable to the throttle lever, install the cruise control cable to the bracket, install the cruise control cable to the throttle lever, check for complete throttle opening and closing positions by operating the accelerator pedal and install the fuel injection sight shield.
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque when installing the accelerator control bracket bolts?
A:
The recommended torque is 16 N.m (12 lb-ft).
By Bob
GM Specialist
02/11/2022See more FAQs (6)