Notes: with 51-1/8" (1299 mm) Long Driveshaft;Supplied as new; Measurement is taken from end of input shaft to center of U-Joint
Greasable: No
Length: 51.125"
Length (mm): 1299
Material: Steel
Measurement Method: Measurement is taken from the centerline of the U-Joint located at the slip yoke end to the centerline of the furthest U-Joint on the opposite end of the collapsed Prop Shaft
Product Condition: Remanufactured
Part Description: 2004 Chevrolet Silverado 1500 Remanufactured Driveshaft/ Prop Shaft
More Info
Vehicle Fitment
2004 Chevrolet Silverado 1500 | All Trims | All Engines
Part Description: 2004 Chevrolet Silverado 1500 Rear Axle Drive Shaft
More Info
Vehicle Fitment
2004 Chevrolet Silverado 1500 | Base, Hybrid, LS, LT, SS, WT, Z71 | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L ELECTRIC/GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
FAQ for Driveshaft Repair
Q: What is the proper way to install the one-piece propeller shaft?
A:
The proper way is to install the propeller shaft, the yoke retainers, and bolts, and then lower the vehicle.
By Bob
GM Specialist
29/10/2022
Q: What is the proper way to install the front propeller shaft?
A:
The proper way is to install a new clamp, the propeller shaft splines, the propeller shaft, the yoke retainers, and the transfer case shield.
By Bob
GM Specialist
29/10/2022
Q: What is the proper way to install the two-piece propeller shaft?
A:
The proper way is to install the front propeller shaft, the front propeller shaft, the yoke retainers, the bolts, the center bearing support, the rear propeller shaft slip yoke, and the rear propeller shaft.
By Bob
GM Specialist
29/10/2022
Q: What is the removal procedure for the front propeller shaft?
A:
The procedure is to remove the transfer case shield, the rear propeller shaft boot clamp, the bolts, the yoke retainers, and the propeller shaft.
By Bob
GM Specialist
29/10/2022
Q: What is the removal procedure for the one-piece propeller shaft?
A:
The procedure is to remove the bolts, the yoke retainers, and the propeller shaft.
By Bob
GM Specialist
29/10/2022
Q: What is the description for the front propeller shaft?
A:
The description is that the front propeller shaft transmits rotating force from the transfer case to the front differential when the transfer case is engaged. The front propeller shaft connects to the transfer case using a splined slip joint.
By Bob
GM Specialist
29/10/2022
Q: What is the removal procedure for the two-piece propeller shaft?
A:
The procedure is to remove the clamp securing the boot, the bolts, the yoke retainers, the rear propeller shaft, the center bearing support, and the front propeller shaft.
By Bob
GM Specialist
29/10/2022
See more FAQs (2)
FAQ for Other Repair Info
Q: What is the removal procedure for the rear axle shaft and/or gasket?
A:
The procedure is to remove the flange bolts, the Axle Shaft, and the gasket, and then clean the axle shaft flange and the outside face of the hub assembly.
Q: What is the cause of the noise?
A:
The cause is that this noise may be caused by a low clearance condition within the Differential in the front axle assembly. In the 2WD mode, the front differential has a large amount of relative motion between the differential pinion and side gears.
Q: What is the proper way to install the front drive axle inner shaft seal and inner shaft bearing?
A:
The proper way is to install the right side bearing, the new Axle Shaft Seal, and the inner axle shaft, and then fill the differential carrier assembly.