< Back ×
My Vehicle Change Vehicle
2001 Chevrolet Astro
< Back to View All
Control Arms & Suspension Rods
- Department
- Prices
OEM (Genuine) 2001 Chevrolet Astro Steering Knuckle Assembly (Rh)
PartNumber: 18060687
Product Specifications- Notes: 2WD; Astro, Safari; Right
- Location: Passenger Side
- Other Names: Knuckle
- Item Dimensions: 15.6 x 11.8 x 10.4 inches
- Item Weight: 17.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15963182, 18060566
- Part Description: 2001 Chevrolet Astro Steering Knuckle Assembly (Rh)
Vehicle Fitment- 2001 Chevrolet Astro | Base, CL, CS, LS, LT | 4 Cyl 2.5 L GAS, 6 Cyl 4.3 L GAS
OEM (Genuine) 2001 Chevrolet Astro Steering Knuckle Assembly (Lh)
PartNumber: 18060688Product Specifications- Notes: 2WD; Astro, Safari; Left
- Location: Driver Side
- Other Names: Knuckle
- Item Dimensions: 15.6 x 11.8 x 10.2 inches
- Item Weight: 17.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 18060565
- Part Description: 2001 Chevrolet Astro Steering Knuckle Assembly (Lh)
Vehicle Fitment- 2001 Chevrolet Astro | Base, CL, CS, LS, LT | 4 Cyl 2.5 L GAS, 6 Cyl 4.3 L GAS
OEM (Genuine) 2001 Chevrolet Astro Knuckle Steering
PartNumber: 18060561
Product Specifications- Notes: 4WD; Astro, Safari; Left
- Location: Driver Side
- Other Names: Knuckle
- Item Dimensions: 16.9 x 13.6 x 7.1 inches
- Item Weight: 19.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15731151
- Part Description: 2001 Chevrolet Astro Knuckle Steering
Vehicle Fitment- 2001 Chevrolet Astro | Base, CL, CS, LS, LT | 6 Cyl 4.3 L GAS
OEM (Genuine) 2001 Chevrolet Astro Knuckle Steering
PartNumber: 18060562
Product Specifications- Notes: 4WD; Astro, Safari; Right
- Location: Passenger Side
- Other Names: Knuckle
- Item Dimensions: 15.3 x 11.5 x 10.4 inches
- Item Weight: 20.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15731152
- Part Description: 2001 Chevrolet Astro Knuckle Steering
Vehicle Fitment- 2001 Chevrolet Astro | Base, CL, CS, LS, LT | 6 Cyl 4.3 L GAS
FAQ for Steering Knuckle Repair
Q: What tools do you need to replace the steering knuckle?
A:
You need to prepare the J 24319B steering linkage and tie rod puller, the J 36607 ball joint separator, and the J 36605 steering knuckle seal installer.
By Bob
GM Specialist
02/11/2022Q: How to remove the steering knuckle?
A:
After raising and supporting the vehicle, you can remove the tire and wheel, unload the torsion bar, and remove the wheel hub and bearing. Then you need to remove the outer tie rod cotter pin and retaining nut, the outer tie rod, the upper ball joint cotter pin, and the retaining nut. After disconnecting the upper ball joint, you can remove the lower ball joint cotter pin and retaining nut. Then you can remove the steering knuckle and the seal from the steering knuckle.
By Bob
GM Specialist
02/11/2022