Notes: This Unit is Pre-Programmed at the Factory;with Tear Tag CLC0;Correct VIN and OE Number Required When Ordering;Emission Calibration/Tear Tag On Front Door Jams, in Trunk, or Under Hood.;with Calibration # 9B1A-BA
Connector/Terminal Configuration: Pin/Male
E-Waste: Yes
Housing Material: Metal
Product Condition: Remanufactured
Removable PROM: No
Terminal Quantity: 104
Part Description: 1999 Ford Ranger Remanufactured Engine Control Computer
Notes: PATS Module Requires Programming after ECM Install.;Correct VIN and OE Number Required When Ordering;All Calibrations with Module ID ML2-8E2;Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN & mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability & starting issues.
Connector/Terminal Configuration: Pin/Male
E-Waste: Yes
Housing Material: Metal
Product Condition: Remanufactured
Removable PROM: No
Terminal Quantity: 104
Part Description: 1999 Ford Ranger Remanufactured Engine Control Computer
Notes: This Unit is Pre-Programmed at the Factory;Correct VIN and OE Number Required When Ordering;with Calibration # 8-49A, 9B1M-AA, AB;Emission Calibration/Tear Tag On Front Door Jams, in Trunk, or Under Hood.
Connector/Terminal Configuration: Pin/Male
E-Waste: Yes
Housing Material: Metal
Product Condition: Remanufactured
Removable PROM: No
Terminal Quantity: 104
Part Description: 1999 Ford Ranger Remanufactured Engine Control Computer
Notes: Correct VIN and OE Number Required When Ordering;PATS Module Requires Programming after ECM Install.;All Calibrations with Module ID ML2-8C2;Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN & mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability & starting issues.
Connector/Terminal Configuration: Pin/Male
E-Waste: Yes
Housing Material: Metal
Product Condition: Remanufactured
Removable PROM: No
Terminal Quantity: 104
Part Description: 1999 Ford Ranger Remanufactured Engine Control Computer
Notes: All Calibrations with Module ID ML2-8E1;PATS Module Requires Programming after ECM Install.;Correct VIN and OE Number Required When Ordering;Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN & mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability & starting issues.
Connector/Terminal Configuration: Pin/Male
E-Waste: Yes
Housing Material: Metal
Product Condition: Remanufactured
Removable PROM: No
Terminal Quantity: 104
Part Description: 1999 Ford Ranger Remanufactured Engine Control Computer
Notes: Correct VIN and OE Number Required When Ordering;All Calibrations with Module ID ML2-833;PATS Module Requires Programming after ECM Install.;Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN & mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability & starting issues.
Connector/Terminal Configuration: Pin/Male
E-Waste: Yes
Housing Material: Metal
Product Condition: Remanufactured
Removable PROM: No
Terminal Quantity: 104
Part Description: 1999 Ford Ranger Remanufactured Engine Control Computer
Notes: Correct VIN and OE Number Required When Ordering;PATS Module Requires Programming after ECM Install.;All Calibrations with Module ID ML2-832,832A;Vehicle specific Flash programming Reqd ON or OFF the vehicle.Accurate VIN & mileage are req'd
Connector/Terminal Configuration: Pin/Male
E-Waste: Yes
Housing Material: Metal
Product Condition: Remanufactured
Removable PROM: No
Terminal Quantity: 104
Part Description: 1999 Ford Ranger Remanufactured Engine Control Computer