< Back ×
My Vehicle Change Vehicle
2010 GMC Canyon
< Back to View All
Steering Racks & Gearboxes
- Department
- Prices
OEM (Genuine) 2010 GMC Canyon Gear Assembly
PartNumber: 15951338
Product Specifications- Notes: W/O 4WD, Z85
- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 29.6 x 7.4 x 6.9 inches
- Item Weight: 7.60 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25817575, 15864178, 15921544
- Part Description: 2010 GMC Canyon Gear Assembly
Vehicle Fitment- 2010 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
$451.30 MSRP:$746.95You Save: $295.65 (40%)OEM (Genuine) 2010 GMC Canyon Gear Asm-Steering (W/ Steering Linkage Tie Rod)
PartNumber: 25912269
Product Specifications- Notes: W/4WD;W/O 4WD, Z71; Canyon, Colorado; 2WD; Chassis Pkg.;Canyon, Colorado; 2WD; Off Road Pkg.;Canyon, Colorado; 4WD
- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 64.1 x 13.5 x 12.2 inches
- Item Weight: 24.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2010 GMC Canyon Gear Asm-Steering (W/ Steering Linkage Tie Rod)
Vehicle Fitment- 2010 GMC Canyon | SLE, SLT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
$505.71 MSRP:$954.18You Save: $448.47 (48%)OEM (Genuine) 2010 GMC Canyon Gear Asm-Steering (W/ Steering Linkage Tie Rod)
PartNumber: 15951337
Product Specifications- Notes: W/O 4WD, Zq8; Canyon, Colorado; 2WD; Sport Chassis Pkg.
- Other Names: Gear Assembly, Steering Gear
- Item Dimensions: 61.6 x 12.1 x 10.2 inches
- Item Weight: 20.00 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2010 GMC Canyon Gear Asm-Steering (W/ Steering Linkage Tie Rod)
Vehicle Fitment- 2010 GMC Canyon | SLE, SLT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
FAQ for Steering Gearbox Repair
Q: What is the recommended torque for the isolator clamp bolt?
A:
The recommended torque is 100 Nm (74 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What should I ensure before disconnecting the Steering Gear?
A:
You need to ensure that the steering wheel must be secured in position.
By Bob
GM Specialist
01/11/2022Q: How to disassemble the Steering Gear Cylinder Pipe Assembly and Seals?
A:
You need to loosen both cylinder line fittings on the cylinder end of the gear assembly and loosen both fittings on the cylinder line assemblies at the valve end of the gear assembly. Then you need to remove both cylinder line assemblies from the rack and pinion gear assembly and remove and discard the O-ring seals.
By Bob
GM Specialist
01/11/2022Q: How to adjust the Steering Gear Rack Bearing Preload?
A:
You need to loosen the adjuster plug lock nut and tighten the adjuster plug. Then you need to tighten the adjuster plug lock nut to the steering gear housing.
By Bob
GM Specialist
01/11/2022Q: How to assemble the Steering Gear Cylinder Pipe Assembly and Seals?
A:
You need to inspect the cylinder lines and replace the parts as needed. Then you need to install the new O-ring seals to the valve end of the cylinder lines. Finally, you need to install the cylinder line assemblies to the gear assembly.
By Bob
GM Specialist
01/11/2022Q: How to disassemble the Steering Gear Boot and Breather Tube?
A:
You need to remove the outer tie rod and remove the hexagon jam nut from the inner tie rod assembly. Then you need to remove the tie rod end clamp from the rack and pinion boot and remove the boot clamp from the rack and pinion boot with side cutters. After that, you need to discard the boot clamp. Finally, you need to remove the rack and pinion boot, and the breather tube.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the long bolts?
A:
The recommended torque is 130 Nm (96 lb-ft).
By Bob
GM Specialist
01/11/2022Q: Which tool is required during the Steering Gear Boot and Breather Tube replacement?
A:
You need to prepare the J 22610 Keystone Clamp Pliers.
By Bob
GM Specialist
01/11/2022Q: What should I ensure during the Steering Gear Boot and Breather Tube assembly?
A:
You need to ensure that the rack and pinion boot must not twisted, puckered, or out of shape in any way.
By Bob
GM Specialist
01/11/2022Q: Which tool is required during the Steering Gear Rack Bearing Preload adjustment?
A:
You need to prepare the J 45059 Angle Meter.
By Bob
GM Specialist
01/11/2022See more FAQs (7)