Part Description: 2010 GMC Canyon Hinge Asm-Rear Side Door Lower
More Info
Vehicle Fitment
2010 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
FAQ for Door Hinge Repair
Q: What is the recommended torque for the bolts retaining the hinge to the body?
A:
The recommended torque is 25 Nm (18.4 lb-ft).
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the bolt retaining the front door check link to the body?
A:
The recommended torque is 25 Nm (18.4 lb-ft).
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the bolts retaining the door side door hinge to the door?
A:
The recommended torque is 27 Nm (20 lb-ft).
By Bob
GM Specialist
01/11/2022
Q: How to remove the Rear Side Door Hinge?
A:
You need to remove the bolt retaining the rear door check link to the body, remove the rear door wiring harness grommet from the body, and disconnect the door wiring harness connectors. Then you need to remove the bolts retaining the rear door hinge keeper straps and lift the rear door up off the body side hinges and place them on a clean protected surface. After that, you need to clean the mounting surfaces of the body side hinges with a clean rag and mark the rear door hinge locations with a grease pencil or other suitable marker, and you need to remove the bolts retaining the body side hinges to the body. Finally, you need to remove the hinges from the body.
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the bolts retaining the body side door hinge to the body?
A:
The recommended torque is 27 Nm (20 lb-ft).
By Bob
GM Specialist
01/11/2022
Q: What is the recommended torque for the bolts retaining the rear door hinge keeper straps?
A:
The recommended torque is 25 Nm (18.4 lb-ft).
By Bob
GM Specialist
01/11/2022
Q: How to remove the Rear Side Access Door Hinge?
A:
You need to open the front and rear side access doors, clean the mounting surfaces of the hinges with a clean rag and mark the rear door hinge locations on each surface with a grease pencil, or other suitable markers. Then you need to support the rear side access door and remove the bolts retaining the hinge to the door. After that, you need to remove the bolts retaining the hinge to the body. Finally, you need to remove the rear side access door hinge from the body.
By Bob
GM Specialist
01/11/2022
Q: How to install the Rear Side Door Hinge?
A:
You need to position the body side rear door hinge to the alignment marks, install the bolts retaining the body side door hinge to the body, and lower the rear door down onto the body side hinge straps. Then you need to install the bolts retaining the rear door hinge keeper straps, connect the rear door wiring harness connectors, and install the rear door wiring harness grommet to the body. After that, you need to install the bolt retaining the rear door check link to the body. Finally, you need to inspect the door for proper operation and alignment.
By Bob
GM Specialist
01/11/2022
Q: How to install the Rear Side Access Door Hinge?
A:
You need to position the rear side access door hinge to the alignment marks and install the bolts retaining the hinge to the body. Then you need to install the bolts retaining the hinge to the door and remove the support from the rear side access door. Finally, you need to inspect the door for proper operation and alignment.
By Bob
GM Specialist
01/11/2022
Q: How to install the Front Side Door Hinge?
A:
You need to position the body side front door hinge to the alignment marks and install the bolts retaining the body side door hinge to the body. Then you need to lower the front door and install the bolts retaining the front door hinge keeper straps. After that, you need to connect the front door wiring harness connectors, install the front door wiring harness grommet to the body, and install the bolt retaining the front door check link to the body. Finally, you need to inspect the door for proper operation and alignment.
By Bob
GM Specialist
01/11/2022
See more FAQs (18)
FAQ for Other Repair Info
Q: How to remove the Front Side Door Check Link?
A:
You need to remove the front door trim panel, the front door water deflector, and the bolt retaining the front Door Check link to the body. Then you need to remove the nuts retaining the front door check link to the door. Finally, you can remove the front door check link from the door.
Q: How to install the Door Jamb Switch?
A:
You need to connect the electrical connector to the Door Jamb Switch and install the door jamb switch to the body. Then you need to install the screw retaining the door jam switch to the body. Finally, you need to close the door.
Q: How to install the Upper Rear Side Access Door Latch?
A:
You need to install the upper latch to the rear side access door and install the lower bolts retaining the upper latch to the rear side access door. Then you need to connect the upper latch rod to the latch and close the rear side access door to self-align the upper latch and tighten the lower rear side access door upper latch bolts. After that, you need to open the rear side access door, install the upper rear side access door upper latch bolt, and install the rear side access door trim panel. Finally, you need to close the rear side access door.