< Back ×
My Vehicle Change Vehicle
2010 Chevrolet Traverse
< Back to View All
Valves, Valve Covers & Valvetrain
- Department
- Prices
OEM (Genuine) 2010 Chevrolet Traverse Filler Cap O-Ring
PartNumber: 12572638
Product Specifications- Other Names: Filler Cap O-Ring, Valve Lifters
- Item Dimensions: 3.1 x 3.0 x 3.0 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaced by: 12686787
- Part Description: 2010 Chevrolet Traverse Filler Cap O-Ring
Vehicle Fitment- 2010 Chevrolet Traverse | High Country, L, LS, LT, LTZ, Premier, RS | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
$14.00 MSRP:$23.17You Save: $9.17 (40%)
OEM (Genuine) 2010 Chevrolet Traverse Valve Springs
PartNumber: 12592506
Product Specifications- Notes: Enclave, Traverse
- Other Names: Valve Spring
- Item Dimensions: 2.4 x 1.6 x 1.1 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2010 Chevrolet Traverse Valve Springs
Vehicle Fitment- 2010 Chevrolet Traverse | LS, LT, LTZ | 6 Cyl 3.6 L GAS
$4.66 MSRP:$7.39You Save: $2.73 (37%)
FAQ for Valve Spring Repair
Q: What should be noticed while removing the valve stem oil seal and valve spring-right side?
A:
If EN 46106 is not installed, the crankshaft may rotate. If the crankshaft rotates, disassembly and reassembly of the entire camshaft timing system may be required.
By Bob
GM Specialist
02/11/2022Q: How to install the valve stem oil seal and valve spring-left side?
A:
You shall install the valve stem seal, the valve spring, the valve spring retainer, the valve spring keepers, the spark plugs, the rocker arms and camshafts, and the starter motor.
By Bob
GM Specialist
02/11/2022Q: How to remove the valve stem oil seal and valve spring-left side?
A:
You shall remove the starter motor, the camshafts and rocker arms, the spark plug, the rocker arm, the valve keepers, the valve spring retainer, the valve spring, and the valve stem seal.
By Bob
GM Specialist
02/11/2022Q: What kind of tools will be required in the replacement of the valve stem oil seal and valve spring-right side?
A:
The tools required include EN 46106 Flywheel Holding Tool, EN 46110 On-Vehicle Valve Spring Compressor, EN 46116 Valve Stem Seal Remover/Installer, and J 39313 Spark Plug Port Adapter.
By Bob
GM Specialist
02/11/2022Q: How do I remove the left side Valve Stem Oil Seal and Valve Spring?
A:
Start with installing the flywheel Holding Tool to prevent the crankshaft from rotating. Remove the camshafts and rocker arms, the spark plug, and the rocker arm. Use the Spark Plug Port Adapter to the applicable cylinder and connect it to a compressed air source. Use the On-Vehicle Valve Spring Compressor on the desired cylinder and tighten the compressor nut. Remove the valve keepers and spring. Use the seal remover to remove the valve stem seal.
By Omar
GM Specialist
11/03/2022Q: How do I remove the right side Valve Stem Oil Seal and Valve Spring?
A:
Start with installing the flywheel Holding Tool to prevent the crankshaft from rotating. Remove the camshafts and rocker arms and the spark plug from the applicable cylinder. Use the Spark Plug Port Adapter to the applicable cylinder and connect it to a compressed air source. Use the On-Vehicle Valve Spring Compressor on the desired cylinder and tighten the compressor nut. Remove the valve keepers and spring. Use the seal remover to remove the valve stem seal.
By Bob
GM Specialist
11/03/2022Q: What special tools will I be needing when servicing the Valve Stem Oil Seal and Valve Spring?
A:
You will be needing a Flywheel Holding Tool, On-Vehicle Valve Spring Compressor, a Valve Stem Seal Remover/Installer, and a Spark Plug Port Adapter.
By Bob
GM Specialist
03/03/2022See more FAQs (2)