< Back ×
My Vehicle Change Vehicle
2010 Chevrolet Express 3500
< Back to View All
Fuses & Fuse Box
- Department
- Prices
OEM (Genuine) 2010 Chevrolet Express 3500 Junction Block
PartNumber: 22737795
Product Specifications- Notes: Junction Block, Engine Compartment, W/6.6 Liter
- Other Names: Junction Block
- Item Dimensions: 12.4 x 10.3 x 8.2 inches
- Item Weight: 4.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 20928294, 20902964
- Part Description: 2010 Chevrolet Express 3500 Junction Block
Vehicle Fitment- 2010 Chevrolet Express 3500 | Base, LS, LT | 8 Cyl 4.8 L FLEX, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.6 L DIESEL
$151.12 MSRP:$239.95You Save: $88.83 (38%)OEM (Genuine) 2010 Chevrolet Express 3500 Junction Block
PartNumber: 25888290
Product Specifications- Notes: Junction Block, Engine Compartment, W/O 6.6 Liter
- Other Names: Junction Block
- Item Dimensions: 13.9 x 7.0 x 6.8 inches
- Item Weight: 3.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25855771, 15938398
- Part Description: 2010 Chevrolet Express 3500 Junction Block
Vehicle Fitment- 2010 Chevrolet Express 3500 | Base, LS, LT | 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
OEM (Genuine) 2010 Chevrolet Express 3500 Junction Block
PartNumber: 84184393
Product Specifications- Notes: Junction Block, Body
- Other Names: Junction Block
- Item Dimensions: 10.4 x 8.1 x 8.3 inches
- Item Weight: 2.20 Pounds
- Fitment Type: Direct Replacement
- Replaces: 20995978, 22778075
- Part Description: 2010 Chevrolet Express 3500 Junction Block
Vehicle Fitment- 2010 Chevrolet Express 3500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
FAQ for Fuse Box Repair
Q: What is the recommended torque for the conductive M6 nut?
A:
The recommended torque is 8 Nm (71 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the M7 bolt?
A:
The recommended torque is 9 Nm (80 lb in).
By Bob
GM Specialist
01/11/2022Q: How do you remove the accessory wiring junction block?
A:
You need to disconnect the negative battery cable, press tabs inward to lift and remove the small junction block cover, press tabs inward to lift and remove the large junction block cover, note the location and remove harness end nuts, and then remove harness ends from fuse block relay center, the fuse block center bolts and remove fuse relay center from the junction block, the chassis harness, the I/P harness, the engine harness, and the forward LP harness, and the junction block base.
By Bob
GM Specialist
01/11/2022Q: What is the installation procedure for the accessory wiring junction block?
A:
The procedure is to install the junction block base, the chassis harness, the I/P harness, the engine harness, and the forward LP harness, the fuse relay center into the junction block, the fuse block center bolts, the harness ends on the fuse block relay center and the harness end nuts, press tabs inward to lift and remove the large junction block cover, press tabs inward to lift and remove the small junction block cover, and then connect the negative battery cable.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the conductive M8 nut?
A:
The recommended torque is 22 Nm (16 lb in).
By Bob
GM Specialist
01/11/2022Q: How do you remove the body wiring harness junction block?
A:
You need to disconnect the battery negative cable, remove the driver's seat, the junction block cover, the positive battery cable nut from the junction block, and the positive battery cable from the junction block, disconnect the electrical connectors from the junction block if equipped with YF7, completely loosen the junction block caged bolts, release the tabs that retain the junction block to the junction block base, and then remove the junction block from the block base, the junction block base nuts, the wiring harness from the junction block base and the junction block base from the floor.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the M6 nut?
A:
The recommended torque is 8 Nm (71 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the installation procedure for the body wiring harness junction block?
A:
The procedure is to install the wiring harness to the junction block base, the junction block base to the floor studs, the junction block base nuts to the floor studs, and the junction block to the junction block base, connect the electrical connectors (if equipped with YF7) and the positive battery cable to the junction block, install the positive battery cable nut, the junction block cover, and the driver's seat, and then connect the battery negative cable.
By Bob
GM Specialist
01/11/2022See more FAQs (3)