< Back ×
My Vehicle Change Vehicle
2010 Chevrolet Equinox
< Back to View All
Cameras & Driver Safety
- Department
- Brands
- Prices
OEM (Genuine) 2010 Chevrolet Equinox Reverse Sensor
PartNumber: 20777093
Product Specifications- Other Names: Park Sensor, Reverse Sensor, Sensor
- Item Dimensions: 2.7 x 1.8 x 1.5 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2010 Chevrolet Equinox Reverse Sensor
Vehicle Fitment- 2010 Chevrolet Equinox | LS, LT, LTZ | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
$176.64 MSRP:$277.81You Save: $101.17 (37%)
Dorman® Replacement Front Parking Sensor for 2010 Chevrolet Equinox
PartNumber: 684-012Product Specifications- Connector Gender: Male
- Mounting Hardware Included: No
- Package Contents: 1 Sensor
- Terminal Gender: Male
- Terminal Quantity: 3
- Terminal Type: Pin
- Universal Or Specific Fit: Specific
- UPC: 885484447943
- Wiring Harness Included: No
- Part Description: 2010 Chevrolet Equinox Replacement Front Parking Sensor
Vehicle Fitment- 2010 Chevrolet Equinox | All Trims | All Engines
$40.74
FAQ for Parking Sensors Repair
Q: How do you replace the Rear Object Sensor?
A:
You can remove the rear bumper fascia, then disconnect the electrical connector from the rear object sensor, lift the locking tabs on the housing and finally remove the rear object sensor.
By Bob
GM Specialist
02/11/2022Q: What must you do if replacing the sensor housing?
A:
You must paint the sensor housing if replacing the sensor housing.
By Bob
GM Specialist
02/11/2022Q: What is the proper way to install the Rear Object Sensor?
A:
You can paint the rear object sensor, ensure the paint does not exceed 6 mils, insert the sensor into the housing, then connect the electrical connector to the rear object sensor and finally install the rear bumper fascia.
By Bob
GM Specialist
02/11/2022Q: How do you replace the Rear Object Sensor Housing?
A:
You can remove the rear fascia, disconnect the sensor harness, remove the sensor from the sensor housing, sand/grind sonic weld plastic residue from the fascia, apply structural adhesive epoxy, Lord Fusor(TM) 127EZ or equivalent to fascia at the mating surface, install the sensor housing to the fascia, allow adhesive to cure, install the sensor to the sensor housing, connect the electrical harness and finally install the rear fascia.
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque when you tighten the information center telltale assembly screws?
A:
You can tighten the screws to 2 Nm (18 lb in).
By Bob
GM Specialist
01/11/2022Q: What should you remove before replacing the Rear Object Alarm Module?
A:
You should remove the left body side trim panel before replacing the Rear Object Alarm Module.
By Bob
GM Specialist
01/11/2022Q: How many screws does the information center telltale assembly have?
A:
The information center telltale assembly has a total of 2 screws.
By Bob
GM Specialist
01/11/2022Q: How many retainers does the Rear Object Alarm Module have?
A:
The Rear Object Alarm Module has a total of 3 retainers.
By Bob
GM Specialist
01/11/2022See more FAQs (3)