< Back ×
My Vehicle Change Vehicle
2010 Chevrolet Equinox
< Back to View All
Door Handles, Locks & Related Parts
- Department
- Prices
OEM (Genuine) 2010 Chevrolet Equinox Lift Gate
PartNumber: 84680007
Product Specifications- Other Names: Lift Gate
- Item Dimensions: 11.0 x 64.0 x 55.1 inches
- Item Weight: 42.40 Pounds
- Fitment Type: Direct Replacement
- Replaces: 25959021
- Part Description: 2010 Chevrolet Equinox Lift Gate
Vehicle Fitment- 2010 Chevrolet Equinox | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
$1153.16 MSRP:$1739.66You Save: $586.50 (34%)
FAQ for Liftgates Repair
Q: How do you install the Liftgate Window?
A:
You can install the liftgate window into the opening, install the rear end spoiler and the rear window wiper arm, connect the liftgate window defogger electrical connectors, install the liftgate lower trim finish panel, remove the double layer of masking tape around the perimeter of the painted surfaces and the interior trim and then close the liftgate.
By Bob
GM Specialist
01/11/2022Q: What should you remove before replacing the Liftgate Hydraulic Pump Insulator?
A:
You should remove the liftgate hydraulic pump and the liftgate hydraulic pump cover.
By Bob
GM Specialist
01/11/2022Q: What must rest in the horizontal position for one minute before the hydraulic fluid level is inspected?
A:
The liftgate hydraulic actuator pump must rest in the horizontal position for one minute before the hydraulic fluid level is inspected.
By Bob
GM Specialist
01/11/2022Q: How do you replace the Liftgate Window?
A:
You can open the liftgate, remove the liftgate lower trim finish panel, disconnect the electrical connectors, remove the rear window wiper arm and the rear end spoiler, cover the upper dash pad, the defroster outlets, the A/C outlets, the seats, and carpeting, cut the lace from the sides and the top edge of the window, remove the window from the urethane adhesive, remove the bottom corners of the window from the urethane adhesive and remove the window from the vehicle.
By Bob
GM Specialist
01/11/2022Q: How many retainers does the tie wrap have?
A:
The tie wrap has a total of 8 retainers.
By Bob
GM Specialist
01/11/2022Q: What should you do before replacing the Liftgate Hydraulic Actuator?
A:
You should open and support the liftgate, disconnect the battery, remove the left body side trim panel, position a protective covering over the interior and the adjacent body panels, and disconnect the hydraulic hose from the hydraulic pump.
By Bob
GM Specialist
01/11/2022Q: What should you remove before replacing the Liftgate Side Upper Sensor (Equinox)?
A:
You should remove the upper liftgate trim finish panel.
By Bob
GM Specialist
01/11/2022Q: What should you ensure when removing or installing the Liftgate Hydraulic Actuator Hose?
A:
You should ensure that the quick connects are not distorted during removal or installation.
By Bob
GM Specialist
01/11/2022Q: How do you bleed the Liftgate Hydraulic System?
A:
You can cycle the liftgate 3-5 times, inspect the fluid level and refer to Liftgate Hydraulic System Refilling if adding fluid is required.
By Bob
GM Specialist
01/11/2022Q: How many retainers does the liftgate side upper sensor have?
A:
The liftgate side upper sensor has a total of 4 retainers.
By Bob
GM Specialist
01/11/2022See more FAQs (19)