< Back ×
My Vehicle Change Vehicle
2010 Chevrolet Camaro
< Back to View All
Driveline, Axles & 4WD
- Department
- Prices
OEM (Genuine) 2010 Chevrolet Camaro Boot Kit-Rear Wheel Drive Shaft Outer Cv Joint
PartNumber: 92228290
Product Specifications- Notes: W/O Zl1, Z28; Camaro
- Location: Driver Side; Passenger Side
- Other Names: Outer Boot
- Item Dimensions: 7.1 x 4.7 x 4.3 inches
- Item Weight: 0.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2010 Chevrolet Camaro Boot Kit-Rear Wheel Drive Shaft Outer Cv Joint
Vehicle Fitment- 2010 Chevrolet Camaro | LS, LT, SS, Z/28, ZL1 | 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
OEM (Genuine) 2010 Chevrolet Camaro Boot
PartNumber: 92233971
Product Specifications- Notes: Camaro; W/O Zl1 & Z28
- Location: Driver Side; Passenger Side
- Other Names: Boot, Dust Cover
- Item Dimensions: 9.8 x 4.1 x 3.6 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2010 Chevrolet Camaro Boot
Vehicle Fitment- 2010 Chevrolet Camaro | LS, LT, SS, Z/28, ZL1 | 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
OEM (Genuine) 2010 Chevrolet Camaro Boot Kit, Rear Wheel Drive Shaft Inner Cv Joint
PartNumber: 92228294
Product Specifications- Notes: W/O Zl1, Z28; Camaro
- Location: Driver Side; Passenger Side
- Other Names: Inner Boot
- Item Dimensions: 6.1 x 4.9 x 5.0 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2010 Chevrolet Camaro Boot Kit, Rear Wheel Drive Shaft Inner Cv Joint
Vehicle Fitment- 2010 Chevrolet Camaro | LS, LT, SS | 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
OEM (Genuine) 2010 Chevrolet Camaro Boot, Propeller Shaft Slip Yoke
PartNumber: 92228332
Product Specifications- Notes: W/O Zl1, Z28
- Other Names: Boot Kit
- Item Dimensions: 2.0 x 1.9 x 1.8 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2010 Chevrolet Camaro Boot, Propeller Shaft Slip Yoke
Vehicle Fitment- 2010 Chevrolet Camaro | LS, LT, SS | 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
FAQ for Cv Joint Boot Repair
Q: What is the rear wheel drive shaft outer joint and boot assemble procedure?
A:
First place the boot and the clamp on the wheel drive shaft. Make sure that the boot is properly seated in the groove in the wheel drive shaft. Next install the retaining ring on the wheel drive shaft, close the boot clamp until the gap measures 2.15 mm, and install the CV joint on the wheel drive shaft. Place half of the lubricant inside the CV boot, and remove any excess lubricant on the CV joint housing of the boot. Use the CH 48894 to close the boot clamp and install the wheel drive shaft.
By Omar
GM Specialist
18/10/2021Q: What is the rear wheel drive shaft inner joint boot disassembly procedure?
A:
First, remove the wheel drive shaft, and remove the outer CV joint and boot. Next, remove the outer boot clamp, and remove the CV joint boot from the CV joint and the wheel drive shaft.
By Bob
GM Specialist
17/10/2021