Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2010 Chevrolet Aveo Vehicle Speed Sensors

2010 Chevrolet Aveo Vehicle Speed Sensors

My Vehicle Change Vehicle
2010 Chevrolet Aveo
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Transmissions Components & Shifters
  • Department
  • Prices

1 Product found

7 Q&A for Vehicle Speed Sensors Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2010 Chevrolet Aveo Vehicle Speed Sensor Diagram - 96806579
    View Related Parts

    OEM (Genuine) 2010 Chevrolet Aveo Vehicle Speed Sensor

    PartNumber: 96806579
    OEM 2010 Chevrolet Aveo Vehicle Speed Sensor - 96806579
    Product Specifications
    • Notes: Aveo, Aveo5; All
    • Other Names: Vehicle Speed Sensor
    • Item Dimensions: 3.1 x 2.1 x 1.0 inches
    • Item Weight: 0.40 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2010 Chevrolet Aveo Vehicle Speed Sensor
    More Info
    Vehicle Fitment
    • 2010 Chevrolet Aveo | LS, LT | 4 Cyl 1.6 L GAS
    $36.32 MSRP: $60.12
    You Save: $23.80 (40%)

FAQ for Vehicle Speed Sensors Repair

Q: How do I install the Output Speed Sensor (OSS)?
A:
Start with installing the new O-ring on the OSS sensor. Next, install the sensor. Then connect the sensor electrical connector and the negative battery cable.
By Bob
GM Specialist
25/01/2022
Q: How do I remove the Output Speed Sensor?
A:
Start with disconnecting the negative battery cable and the output shaft speed sensor electrical connector. Next, remove the OSS sensor from the transaxle by removing the retaining bolt attaching it to the vehicle.
By Bob
GM Specialist
24/01/2022
Q: How do you remove the speedometer-driven gear on a manual transmission?
A:
You will need to disconnect the vehicle speed sensor, remove the gear assembly bolt, and remover the speedometer drive gear from the housing.
By Omar
GM Specialist
22/01/2022
Q: How do you remove the speedometer-driven gear?
A:
You will need to disconnect the speed sensor connector, the speedometer retaining bolt, and the gear/housing.
By Bob
GM Specialist
22/01/2022
Q: What is the input speed sensor installation procedure?
A:
First, install a new O-ring, the ISS sensor, and the ISS sensor bolt and tighten to 5 Nm. Next, connect the ISS sensor electrical connector and the negative battery cable.
By Bob
GM Specialist
21/01/2022
Q: What is the torque spec for the speedometer housing bolt?
A:
4Nm (35 in./lbs.).
By Omar
GM Specialist
18/01/2022
Q: What Is the torque spec for the transaxle housing bolt?
A:
7Nm (62 in./lbs.).
By Omar
GM Specialist
18/01/2022
See more FAQs (2)

FAQ for Other Repair Info

Q: How do I adjust the Range Selector Lever Cable?
A:
Start with disconnecting the negative battery cable. Then remove the trim panel from the floor console and place the lever in the park. Loosen the control cable adjusting nut. Move the park/neutral position (PNP) switch lever counterclockwise until the lever stops Pull the shift control cable until it is tight and tighten the control cable adjusting nut. Install the floor console trim panel and connect the negative battery.
Q: How do I install the Automatic Transmission Fluid and Filter?
A:
Start with installing a new gasket to the oil strainer. Then install the oil strainer to the valve body by tightening the bolts that attach it to the vehicle to 10 Nm (89 lb. in), the new gasket on the oil pan, and install the oil pan to the transaxle. Lastly, fill the transaxle with transmission fluid.
Q: How do I install the Automatic Transmission Fluid and Filter?
A:
Start with installing the new gasket to the oil strainer, the oil strainer to the valve body, tighten the oil strainer bolts to 10 Nm (89 lb. in), a new gasket on the oil pan, then install the oil pan to the transaxle with the 18 retaining bolts. Lastly, fill the transaxle with transmission fluid.