< Back ×
My Vehicle Change Vehicle
2010 Chevrolet Aveo
< Back to View All
Air Bag
- Department
- Prices
OEM (Genuine) 2010 Chevrolet Aveo Front Sensor
PartNumber: 96808125
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Front Sensor
- Item Dimensions: 3.2 x 1.9 x 1.9 inches
- Item Weight: 0.40 Pounds
- Part Description: 2010 Chevrolet Aveo Front Sensor
Vehicle Fitment- 2010 Chevrolet Aveo | LS, LT | 4 Cyl 1.6 L GAS
$12.14 MSRP:$18.39You Save: $6.25 (34%)
OEM (Genuine) 2010 Chevrolet Aveo Side Sensor
PartNumber: 96808853
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Side Impact Sensor, Side Sensor
- Item Dimensions: 3.4 x 2.2 x 1.6 inches
- Item Weight: 0.50 Pounds
- Part Description: 2010 Chevrolet Aveo Side Sensor
Vehicle Fitment- 2010 Chevrolet Aveo | LS, LT | 4 Cyl 1.6 L GAS
$10.96 MSRP:$16.52You Save: $5.56 (34%)
FAQ for Air Bag Sensor Repair
Q: How do you deploy the airbag module?
A:
You can disconnect the battery cables, remove the knee bolster, untwist the wires near the deployment battery, and dispose of the airbags.
By Bob
GM Specialist
24/01/2022Q: How do you install the I/P inflatable restraint module?
A:
You can install the passenger airbag, the I/P assembly, and the glove box.
By Omar
GM Specialist
24/01/2022Q: How do you remove the steering wheel inflatable restraint module?
A:
You can disconnect the negative battery cable, and remove the steering wheel control switches, and the driver airbag.
By Omar
GM Specialist
22/01/2022Q: What are some SIR Service precautions?
A:
Some precautions are to disable the SIR system and not to expose the inflator modules to extreme heat.
By Bob
GM Specialist
21/01/2022Q: What is the inflatable restraint sensing and diagnostic module installation procedure?
A:
First, install the SDM and the SDM mounting bolts. Tighten the SDM mounting bolts to 10 Nm and connect the SDM electrical connector. Finally, install the connector position assurance lock and the floor console trim bezel.
By Omar
GM Specialist
21/01/2022Q: What is the inflatable restraint sensing and diagnostic module removal procedure?
A:
Remove the floor console trim bezel and the connector position assurance lock. Disconnect the SDM electrical connector and remove the SDM mounting bolts/SDM.
By Bob
GM Specialist
21/01/2022Q: What is the inflatable restraint side impact sensor installation procedure?
A:
First, install the airbag sensor, and the side airbag sensor mounting bolt and tighten to 10 Nm. Connect the side airbag sensor connector and install the lower trim to the center pillar. Finally, connect the negative battery cable.
By Omar
GM Specialist
21/01/2022Q: What is the installation procedure for the I/P inflatable restraint module?
A:
The procedure is to install the passenger airbag module, connect the electrical connector, and install the glove box.
By Omar
GM Specialist
21/01/2022Q: What is the instrument panel inflatable restraint module switch installation procedure?
A:
First, install the passenger airbag disable switch and connect the passenger airbag disable switch connector. Next, connect the negative battery cable.
By Bob
GM Specialist
21/01/2022Q: What is the proper way to install the steering wheel inflatable restraint module?
A:
The proper way is to install the connectors, the driver airbag, and the steering wheel control switches.
By Omar
GM Specialist
20/01/2022See more FAQs (8)