< Back ×
My Vehicle Change Vehicle
2010 Cadillac SRX
< Back to View All
Door Handles, Locks & Related Parts
- Department
- Prices
OEM (Genuine) 2010 Cadillac SRX Lift Gate
PartNumber: 23495091
Product Specifications- Notes: 1st Design
- Other Names: Lift Gate
- Item Dimensions: 66.6 x 54.0 x 15.0 inches
- Item Weight: 43.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 20859022, 20989847
- Part Description: 2010 Cadillac SRX Lift Gate
Vehicle Fitment- 2010 Cadillac SRX | Base, Luxury, Performance, Premium | 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
$1230.54 MSRP:$1856.40You Save: $625.86 (34%)
FAQ for Liftgates Repair
Q: How to replace the liftgate side upper sensor?
A:
You should remove the liftgate upper trim panel and disconnect the electrical connector and the retainers are for one-time use only. They must be replaced after being removed.
By Bob
GM Specialist
01/11/2022Q: How to remove the liftgate window?
A:
You should open the liftgate, remove the liftgate lower trim, disconnect the electrical connectors from the liftgate window rear defogger, remove the rear window wiper arm and the rear spoiler and cover the upper dash pad, defroster outlets, and A/C outlets and seats, and carpeting to protect from broken glass. Then, you should use a utility knife to cut the lace from the sides and the top edge of the window to access the urethane adhesive bead, remove the window from the urethane adhesive, use a long utility knife or similar tool to remove the bottom corners of the window from the urethane adhesive and remove the window from the vehicle.
By Bob
GM Specialist
01/11/2022Q: How to replace the liftgate angle sensor?
A:
You should remove the liftgate lower trim finish panel, disconnect the electrical connector, unsnap the upper portion of the sensor from the liftgate and lift upward to release the tab.
By Bob
GM Specialist
01/11/2022Q: How to bleed the liftgate hydraulic system?
A:
You should inspect if the liftgate hydraulic actuator pump is removed from the vehicle and placed on a clean/level workbench horizontally to the + sign to accurately inspect and add fluid as needed. The liftgate hydraulic actuator pump must rest in the horizontal position for one minute before the hydraulic fluid level is inspected. The level must be above the + mark after cycling the liftgate 3-5 times. You should cycle the liftgate 3-5 times to ensure the proper fluid level and inspect the fluid level.
By Bob
GM Specialist
01/11/2022Q: How to disconnect and connect the liftgate hydraulic actuator hose?
A:
You should reposition the liftgate hydraulic pump, place a clean protective covering over the interior and adjacent areas, reposition the pump so that the lines are on top for minimal leakage, disconnect the quick connect using J-8059-pliers while gently pulling on the hydraulic actuator hose or equivalent, ensure the quick connects are not distorted during removal or installation by overspreading the quick connects, bleed the hydraulic system and refill the hydraulic system.
By Bob
GM Specialist
01/11/2022Q: How many retainers attach to the liftgate side upper sensor?
A:
There are 5 retainers that attach the liftgate side upper sensor.
By Bob
GM Specialist
01/11/2022Q: How to replace the liftgate hydraulic actuator?
A:
You should disconnect the battery, open and support the liftgate, remove the rear compartment floor stowage compartment and the quarter upper trim panel, and position a protective covering over the interior and the adjacent body panels. Then, you should cut the tie wraps and replace them with new tie wraps, reposition the liftgate hydraulic actuator, disconnect the liftgate hydraulic actuator hoses from the hydraulic actuator pump and release the hydraulic hose rubber grommet from the liftgate opening channel. Then, you should disconnect the liftgate hydraulic actuator from the liftgate and liftgate opening and slowly pull the hydraulic hoses from the pillar and inspect the liftgate hydraulic system for proper operation before the final assembly of trim panels.
By Bob
GM Specialist
01/11/2022Q: How to replace the liftgate hydraulic pump cover?
A:
You should open and support the liftgate, disconnect the battery, remove the liftgate hydraulic pump from the vehicle, separate the cover halves from the liftgate pump by releasing the retainer tabs and inspect the liftgate hydraulic system for proper operation before the final assembly of the trim panels.
By Bob
GM Specialist
01/11/2022Q: How to refill the liftgate hydraulic system?
A:
You should remove the liftgate hydraulic pump, position the pump with the fluid reservoir in a vertical position with the filler screw in the up and/or on top position, wipe the surface around the filler screw clean, remove the filler screw, and place on a clean, lint and dust free surface. Then, you should add hydraulic fluid from a clean container, install the filler screw, position the liftgate hydraulic actuator pump on a clean/level workbench horizontally to the + sign to accurately inspect and add fluid as needed and rest in the horizontal position for one minute. Finally, you should install and inspect the pump without the trim and remove the liftgate hydraulic pump after inspection.
By Bob
GM Specialist
01/11/2022Q: How to replace the liftgate hydraulic pump insulator?
A:
You should remove the liftgate hydraulic pump and the liftgate hydraulic pump cover and separate the foam insulator halves from the liftgate hydraulic pump motor.
By Bob
GM Specialist
01/11/2022See more FAQs (8)