< Back ×
My Vehicle Change Vehicle
2009 GMC Envoy
< Back to View All
Interior & Exterior Trim
- Department
- Prices
OEM (Genuine) 2009 GMC Envoy Molding Asm-Windshield Side Garnish *Light Opel Gray
PartNumber: 15782066
Product Specifications- Notes: W/O Xuv, Gray
- Location: Passenger Side
- Other Names: Weatherstrip Pillar Trim
- Item Dimensions: 30.3 x 8.5 x 8.5 inches
- Item Weight: 2.20 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2009 GMC Envoy Molding Asm-Windshield Side Garnish *Light Opel Gray
Vehicle Fitment- 2009 GMC Envoy | Denali, SLE, SLT | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
$26.09 MSRP:$37.51You Save: $11.42 (31%)OEM (Genuine) 2009 GMC Envoy Molding, Windshield Side Garnish
PartNumber: 15782063
Product Specifications- Notes: W/O Xuv, Gray
- Location: Driver Side
- Other Names: Weatherstrip Pillar Trim
- Item Dimensions: 32.6 x 5.9 x 3.3 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2009 GMC Envoy Molding, Windshield Side Garnish
Vehicle Fitment- 2009 GMC Envoy | Denali, SLE, SLT | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
FAQ for Pillar Panels Repair
Q: How do you install the Liftgate Garnish Molding?
A:
You need to install the garnish molding to the liftgate, and the 2 garnish molding retainers on each side.
By Bob
GM Specialist
02/11/2022Q: What is the removal procedure for the Liftgate Garnish Molding?
A:
Use a flat-bladed tool to carefully release the garnish molding retainers, and remove the garnish molding from the liftgate.
By Bob
GM Specialist
02/11/2022Q: What is the recommended torque for the bolt retaining the seat belt anchor to the body?
A:
The recommended torque is 70 Nm (52 lb-ft).
By Bob
GM Specialist
02/11/2022Q: What is the removal procedure for the Center Pillar Garnish Molding?
A:
Remove the front and rear door sill plates, move the seat to a forward position, remove the door opening weatherstrip from the door opening where it interferes with molding removal, release the 4 retaining clips that attach the garnish molding to the center pillar, disconnect the electrical connector from the temperature sensor, if equipped, and remove the garnish molding from the vehicle.
By Bob
GM Specialist
02/11/2022Q: What is the removal procedure for the Body Side Rear Window Garnish Molding (TrailBlazer, Envoy)?
A:
Remove the bolt that retains the seat belt upper anchor to the body and the garnish molding.
By Bob
GM Specialist
02/11/2022Q: How do you install the Front Side Door Water Deflector?
A:
You need to position the water deflector to the door, press the water deflector to the door, install the ORVM wire harness to the door, and install the speaker, and the door trim panel.
By Bob
GM Specialist
01/11/2022Q: What kind of special tools will be used in the removal of the Rear Side Door Trim Panel?
A:
J36796 Clip Removal Tool.
By Bob
GM Specialist
01/11/2022Q: What should be noted when pressing the water deflector to the door?
A:
Ensure that the water deflector forms a proper seal around the surface of the door panel.
By Bob
GM Specialist
01/11/2022Q: How do you install the Door Handle Bezel?
A:
You need to install the bezel to the door, ensuring that all 4 retaining tabs are fully seated, and install the door trim panel to the door.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the retaining screws securing to the trim panel?
A:
The recommended torque is 2.5 Nm (22 lb in).
By Bob
GM Specialist
01/11/2022See more FAQs (7)