Notes: Includes: Gasket; Grade: Actual OE; Terminal Quantity: 6; Availability: Available to Order; Bore Dia: 87.0; Gasket Or Seal Included: Yes; Idle Air Control Motor Included: No; Throttle Body Type: Electric; Throttle Position Sensor Included: Yes
Actuation Type: Electric
Bore Diameter: 87.0 mm
Gasket or Seal Included: Yes
Hardware Included: No
Idle Air Control Motor Included: No
Manufacturer: Hitachi
New or Remanufactured: New
OE Part Number: 12629992
Qty Needed Per Unit: 1
Terminal Connector Type: Blade
Terminal Gender: Male
Terminal Quantity: 6
Throttle Body Type: Electric
Throttle Position Sensor Included: Yes
UPC: 840151060290
Part Description: 2009 Chevrolet Silverado 2500 HD Fuel Injection Throttle Body
More Info
Vehicle Fitment
2009 Chevrolet Silverado 2500 HD | LT | 8 Cyl 6.0L
2009 Chevrolet Silverado 2500 HD | LTZ | 8 Cyl 6.0L
2009 Chevrolet Silverado 2500 HD | WT | 8 Cyl 6.0L
Part Description: 2009 Chevrolet Silverado 2500 HD Throttle Body
More Info
Vehicle Fitment
2009 Chevrolet Silverado 2500 HD | LT, LTZ, WT | 8 Cyl 6.6 L DIESEL
$170.27MSRP: $270.35
You Save: $100.08 (38%)
FAQ for Throttle Body Repair
Q: How do you clean the throttle body?
A:
You can remove the air cleaner outlet duct, inspect the throttle body bore and the throttle plate for deposits, clean the throttle body bore and the throttle plate, install the air cleaner outlet duct and perform the Throttle Learn Procedure.
By Bob
GM Specialist
02/11/2022
Q: What is the reset procedure with a scan tool?
A:
The procedure is to perform the Idle Learn Reset in Module Setup with the ignition on and with the engine off, start the engine, monitor the TB Idle Airflow Compensation parameter, clear the DTCs and return to the diagnostic that referred you here.
By Bob
GM Specialist
02/11/2022
Q: What includes small clamp connectors that provide adaptation to most connectors without damage?
A:
The J 36169-A includes small clamp connectors that provide adaptation to most connectors without damage.
By Bob
GM Specialist
02/11/2022
Q: What can be used to clean the throttle body bore and the throttle plate?
A:
You can use a clean shop towel with GM Top Engine Cleaner, P/N 1052626, or AC-Delco Carburetor Tune-Up Conditioner, P/N X66-P, or an equivalent product.
By Bob
GM Specialist
02/11/2022
Q: What procedure should you perform to measure the voltage at a selected point in a circuit?
A:
You should disconnect the electrical harness connector for the circuit being tested, enable the circuit and/or system being tested, select the V (AC) or V (DC) position on the DMM, connect the positive lead of the DMM to the point of the circuit to be tested and connect the negative lead of the DMM to a good ground.
By Bob
GM Specialist
02/11/2022
Q: How do you replace the Throttle Body Assembly?
A:
You can remove the air cleaner outlet duct, disconnect the engine wiring harness electrical connector, remove the throttle body nuts and bolts, remove the throttle body and remove and discard the throttle body gasket.
By Bob
GM Specialist
02/11/2022
Q: What is the removal procedure for the JST Connectors?
A:
The procedure is to remove the connector from the component, locate the two indents of the terminal position assurance (TPA), raise the TPA on both sides of the connector, view the TPA, release the terminals, and pull the wire out of the back of the connector.
By Bob
GM Specialist
02/11/2022
Q: What tool can be used to release the locking tabs and remove the dress cover?
A:
You can use a small flat-blade tool.
By Bob
GM Specialist
02/11/2022
Q: What tool can be used to raise the TPA on both sides of the connector?
A:
You can use a small flat-blade tool.
By Bob
GM Specialist
02/11/2022
Q: What is the proper way to install the Throttle Body Assembly?
A:
You can install a new throttle body gasket, install the throttle body, bolts and nuts, connect the engine wiring harness electrical connector, install the air cleaner outlet duct, connect a scan tool, operate the accelerator pedal, monitor the throttle angles, verify the vehicle is not in a reduced engine power mode, that the ignition is ON and that the engine is OFF, perform the Throttle Learn Procedure and inspect for coolant leaks.
By Bob
GM Specialist
02/11/2022
See more FAQs (10)
FAQ for Other Repair Info
Q: What is the removal procedure for the Manifold Absolute Pressure Sensor?
A:
The procedure is to remove the intake manifold sight shield, disconnect the engine wiring harness electrical connector, remove the MAP Sensor retainer and remove the MAP sensor.
Q: What is the removal procedure for the Engine Block Valley Cover?
A:
The procedure is to remove the Intake Manifold, the engine valley cover bolts, the engine valley cover, the gasket, the O-ring seals, the oil pressure sensor, and the washer.
Q: What should you disconnect before replacing the Air Cleaner Element?
A:
You should disconnect the air cleaner outlet duct from the air cleaner assembly.