< Back ×
My Vehicle Change Vehicle
2009 Chevrolet Silverado 2500 HD
< Back to View All
Cameras & Driver Safety
- Department
- Brands
- Prices
OEM (Genuine) 2009 Chevrolet Silverado 2500 HD Reverse Sensor
PartNumber: 19115806
Product Specifications- Notes: In Bumper
- Other Names: Reverse Sensor
- Item Dimensions: 2.6 x 1.6 x 1.1 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaced by: 20908127
- Part Description: 2009 Chevrolet Silverado 2500 HD Reverse Sensor
Vehicle Fitment- 2009 Chevrolet Silverado 2500 HD | LT, LTZ, WT | 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
$216.25 MSRP:$326.25You Save: $110.00 (34%)
Dorman® Rear Parking Assist Sensor for 2009 Chevrolet Silverado 2500 HD
PartNumber: 684-060Product Specifications- Connector Gender: Male
- Mounting Hardware Included: No
- Package Contents: 1 Parking Aid Sensor
- Terminal Gender: Male
- Terminal Quantity: 3
- Terminal Type: Pin
- Universal Or Specific Fit: Specific
- UPC: 885484583979
- Wiring Harness Included: No
- Part Description: 2009 Chevrolet Silverado 2500 HD Rear Parking Assist Sensor
Vehicle Fitment- 2009 Chevrolet Silverado 2500 HD | All Trims | All Engines
$25.76OEM (Genuine) 2009 Chevrolet Silverado 2500 HD Reverse Sensor
PartNumber: 19115805
Product Specifications- Notes: Silverado, Sierra; In Step Pad
- Other Names: Reverse Sensor, Sensor
- Item Dimensions: 1.9 x 2.0 x 1.4 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaced by: 25844782
- Part Description: 2009 Chevrolet Silverado 2500 HD Reverse Sensor
Vehicle Fitment- 2009 Chevrolet Silverado 2500 HD | LT, LTZ, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
FAQ for Parking Sensors Repair
Q: What is the removal procedure for the rear object sensor?
A:
The procedure is to disconnect the electrical connector from the rear object sensor, lift the locking tabs on the housing and remove the rear object sensor.
By Bob
GM Specialist
02/11/2022Q: What should you remove before replacing the Rear Object Sensor Housing (Sierra/Silverado)?
A:
You should remove the rear object sensor.
By Bob
GM Specialist
02/11/2022Q: How do you replace the Rear Object Sensor Housing (All Other Vehicles)?
A:
You can remove the center rear bumper step pad or the rear bumper impact bar end cap, disconnect the sensor harness, remove the sensor from the sensor housing, sand/grind sonic weld plastic residue from the fascia, apply structural adhesive epoxy, Lord Fusor(TM) 127EZ or equivalent to fascia at the mating surface, install the sensor housing to the fascia, allow adhesive to cure, install the sensor to the sensor housing, connect the electrical harness and install the center rear bumper step pad or the rear bumper impact bar end cap.
By Bob
GM Specialist
02/11/2022Q: How do you install the rear object sensor?
A:
You can paint the rear object sensor, ensure the paint does not exceed 6 mils, insert the sensor into the housing and connect the electrical connector to the rear object sensor.
By Bob
GM Specialist
02/11/2022Q: How many nuts does the Rear Object Alarm Module have?
A:
The Rear Object Alarm Module has a total of nuts.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque when you tighten the information center telltale screws?
A:
You can tighten the screws to 2 Nm (18 lb in).
By Bob
GM Specialist
01/11/2022Q: What should you remove before replacing the Rear Object Alarm Module?
A:
You should remove the front passenger bucket seat.
By Bob
GM Specialist
01/11/2022Q: How many screws does the information center telltale have?
A:
The information center telltale has a total of 2 screws.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque when you tighten the rear object alarm module nuts?
A:
You can tighten the nuts to 9 Nm (80 lb in).
By Bob
GM Specialist
01/11/2022See more FAQs (4)