< Back ×
My Vehicle Change Vehicle
2009 Chevrolet Express 2500
< Back to View All
Driveline, Axles & 4WD
- Department
- Brands
- Prices
Victor Reinz® Rear Axle Shaft Flange Gasket for 2009 Chevrolet Express 2500
PartNumber: 71-14650-00Product Specifications- Notes: Size- 2-23/32in x 4-7/16in;8 Bolt;Rear
- Bolt Hole Quantity: 8
- Complete: Y
- Contains Applications: Y
- Meets or Exceeds OEM Specs: Y
- Release Wave: 12/15/2017
- Shape: Round
- Thickness: 0.025
- UPC: 023913681265
- Part Description: 2009 Chevrolet Express 2500 Rear Axle Shaft Flange Gasket
Vehicle Fitment- 2009 Chevrolet Express 2500 | All Trims | 8 Cyl 4.8L
- 2009 Chevrolet Express 2500 | All Trims | 8 Cyl 6.0L
- 2009 Chevrolet Express 2500 | All Trims | 8 Cyl 6.6L
$2.72
FAQ for Axle Shaft Flange Gasket Repair
Q: Can you reuse the pinion nut in the installation?
A:
No, do not reuse the pinion nut.
By Omar
GM Specialist
08/02/2022Q: How should you install the pinion yoke properly?
A:
You need to seat the pinion yoke onto the pinion shaft by tapping it with a soft-faced hammer until a few pinion shaft threads show through the yoke.
By Omar
GM Specialist
05/02/2022Q: What do you need to do before disassembly?
A:
You need to observe and mark the positions of all the driveline components, relative to the propeller shaft and the axles before removal. These components include the propeller shafts, drive axles, pinion flanges, output shafts, etc.
By Bob
GM Specialist
04/02/2022Q: What is the recommended torque for the inner shaft seal cover bolts?
A:
The recommended torque is 18 Nm (13 lb-ft).
By Omar
GM Specialist
02/02/2022Q: What is the recommended torque for the pinion nut?
A:
The recommended torque is 339 Nm (250 lb-ft).
By Bob
GM Specialist
01/02/2022Q: What kind of special tools are required for the removal of the Drive Pinion Flange/Yoke and/or Oil Seal (8.6, 9.5 Inch Axles)?
A:
J8614-01-Flange and Pulley Holding Tool, J 38694-Extension Housing Oil Pump/Seal Installer.
By Omar
GM Specialist
29/01/2022Q: What kind of special tools will be used when removing the Front Drive Axle Inner Shaft Seal and Inner Shaft Bearing?
A:
J2619-01 Slide Hammer, J 29369-1 Bushing and Bearing Remover, J 42211 Axle Bearing Installer, J 42738 Seal Installer, J 8092 Universal Driver Handle-3/4 in - 10.
By Bob
GM Specialist
28/01/2022Q: What should you care about while removing the pinon yoke?
A:
You need to carefully pry the seal from the bore. Do not distort or scratch the aluminum case.
By Bob
GM Specialist
27/01/2022Q: What should you do if replacing the left side seal?
A:
You need to disconnect the wheel drive shaft from the inner shaft flange and set it aside. next, remove the inner shaft. then, remove the inner shaft seal cover bolts.
By Omar
GM Specialist
27/01/2022Q: What should you do if the rotating torque is exceeded?
A:
You need to remove the pinion and have a new collapsible spacer installed.
By Bob
GM Specialist
27/01/2022See more FAQs (6)