< Back ×
My Vehicle Change Vehicle
2009 Chevrolet Aveo
< Back to View All
Control Arms & Suspension Rods
- Department
- Prices
OEM (Genuine) 2009 Chevrolet Aveo Steering Knuckle Assembly
PartNumber: 96870494
Product Specifications- Notes: W/O ABS; Aveo, Aveo5; Right; W/O ABS
- Location: Passenger Side
- Other Names: Knuckle
- Item Dimensions: 9.9 x 9.7 x 8.2 inches
- Item Weight: 7.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 96459243
- Part Description: 2009 Chevrolet Aveo Steering Knuckle Assembly
Vehicle Fitment- 2009 Chevrolet Aveo | Base, LS, LT, Special Value | 4 Cyl 1.6 L GAS
$103.11 MSRP:$179.47You Save: $76.36 (43%)
OEM (Genuine) 2009 Chevrolet Aveo Knuckle
PartNumber: 96870491
Product Specifications- Notes: W/ABS; Aveo, Aveo5; Left; W/ABS
- Location: Driver Side
- Other Names: Knuckle
- Item Dimensions: 9.9 x 9.7 x 8.0 inches
- Item Weight: 7.80 Pounds
- Fitment Type: Direct Replacement
- Replaces: 96535190
- Part Description: 2009 Chevrolet Aveo Knuckle
Vehicle Fitment- 2009 Chevrolet Aveo | Base, LS, LT, Special Value | 4 Cyl 1.6 L GAS
$108.43 MSRP:$179.47You Save: $71.04 (40%)
OEM (Genuine) 2009 Chevrolet Aveo Steering Knuckle Assembly
PartNumber: 96870493
Product Specifications- Notes: W/O ABS; Aveo, Aveo5; Left; W/O ABS
- Location: Driver Side
- Other Names: Knuckle
- Item Dimensions: 9.9 x 9.8 x 8.2 inches
- Item Weight: 8.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 96459242
- Part Description: 2009 Chevrolet Aveo Steering Knuckle Assembly
Vehicle Fitment- 2009 Chevrolet Aveo | Base, LS, LT, Special Value | 4 Cyl 1.6 L GAS
OEM (Genuine) 2009 Chevrolet Aveo Steering Knuckle Assembly
PartNumber: 96870492
Product Specifications- Notes: W/ABS; Aveo, Aveo5; Right; W/ABS
- Location: Passenger Side
- Other Names: Knuckle
- Item Dimensions: 10.7 x 8.5 x 7.0 inches
- Item Weight: 7.70 Pounds
- Fitment Type: Direct Replacement
- Replaces: 96535191
- Part Description: 2009 Chevrolet Aveo Steering Knuckle Assembly
Vehicle Fitment- 2009 Chevrolet Aveo | Base, LS, LT, Special Value | 4 Cyl 1.6 L GAS
FAQ for Steering Knuckle Repair
Q: What is the steering knuckle removal procedure?
A:
First remove the front wheels, the axle shaft caulking nut, and the lower ball joint. After that remove the outer tie rod nut, the brake rotor, the brake caliper, and the pads. Next remove the ABS wheel speed sensor, the front strut nuts/bolts, and the knuckle assembly. Finally, remove the wheel hub and the splash shield.
By Bob
GM Specialist
13/12/2021Q: What is the wheel hub, bearing knuckle, and seal replacement disassembly procedure?
A:
First, remove the wheel hub, bearing, knuckle, and brake shield assembly. After that, remove the wheel hub from the wheel bearing, and remove the retaining ring from the knuckle. Next, remove the wheel bearing from the knuckle, discard the wheel bearing, and clean the bore of the knuckle.
By Omar
GM Specialist
11/12/2021Q: Do I need to use any special tool to replace the wheel hub, bearing knuckle, and seal?
A:
Yes, you will need DT-47540, DT-47541, DT-47542, DT-47543, J 214-01, J 22912-B, and J-37105-C.
By Bob
GM Specialist
03/11/2021