< Back ×
My Vehicle Change Vehicle
2009 Cadillac SRX
< Back to View All
Air Bag
- Department
- Prices
OEM (Genuine) 2009 Cadillac SRX Front Sensor
PartNumber: 15946933
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Front Impact Sensor, Front Sensor
- Item Dimensions: 3.4 x 3.1 x 3.1 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2009 Cadillac SRX Front Sensor
Vehicle Fitment- 2009 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
$21.97 MSRP:$33.16You Save: $11.19 (34%)
OEM (Genuine) 2009 Cadillac SRX Side Sensor
PartNumber: 10384760
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Side Impact Sensor, Side Sensor
- Item Dimensions: 3.5 x 3.1 x 3.2 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2009 Cadillac SRX Side Sensor
Vehicle Fitment- 2009 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
FAQ for Air Bag Sensor Repair
Q: What is the removal procedure for the inflatable restraint roof side rail module (right side)?
A:
The procedure is to disable the SIR system, remove the windshield garnish molding, the center pillar garnish moldings, the side door opening garnish molding, the body side rear trim panel, and the connector position assurance (CPA), disconnect the connector, remove the fasteners, lower the headliner, remove the tether and remove the roof rail module.
By Bob
GM Specialist
01/11/2022Q: How do you install the inflatable restraint roof side rail module (right side)?
A:
You can remove any dirt, grease, or other impurities from the mounting surface, insert the roof rail module tether to the windshield pillar, install the mounting fasteners, the roof rail module harness connector, the CPA, the windshield garnish molding, the center pillar garnish moldings and the side door opening garnish molding, enable the SIR system and fully deploy the module before disposal.
By Bob
GM Specialist
01/11/2022Q: What is the proper way to install the left-side inflatable restraint roof-side rail module?
A:
You can remove any dirt, grease, or other impurities from the mounting surface, insert the roof rail module tether to the windshield pillar, install the mounting fasteners, install the roof rail module connector, install the CPA, install the windshield garnish molding, install the center pillar garnish moldings, install the side door opening garnish molding, enable the SIR system and fully deploy the module before disposal.
By Bob
GM Specialist
01/11/2022Q: How do you install the driver or passenger seat side inflatable restraint module?
A:
You can install a new inflatable restraint side impact module bracket, install the 2 bracket mounting bolts, connect the electrical connector, install the CPA to the module electrical connector, install the module to the seat, install the 2 bolts to the inflatable restraint side impact module, install the seat back trim, enable the SIR system and fully deploy the module before disposal.
By Bob
GM Specialist
01/11/2022Q: How do you replace the left side inflatable restraint roof side rail module?
A:
You can disable the SIR system, remove the windshield garnish molding, the center pillar garnish moldings, the side door opening garnish molding, the body side rear trim panel, and the connector position assurance (CPA), lower the headliner, disconnect the connector from the roof rail module, remove the fasteners, remove the tether and remove the roof rail module.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the driver or passenger seat side inflatable restraint module?
A:
The procedure is to disable the SIR system, move the seat to the full forward position, remove the seat back trim, remove the 2 bolts from the inflatable restraint side impact module bracket, remove the module, remove the connector position assurance (CPA) and disconnect the electrical connector from the module.
By Bob
GM Specialist
01/11/2022Q: How many nuts does the inflatable restraint vehicle rollover sensor have?
A:
The inflatable restraint vehicle rollover sensor has a total of 3 nuts.
By Bob
GM Specialist
01/11/2022Q: How do you replace the inflatable restraint side impact sensor?
A:
You can disable the SIR system, remove the center pillar trim panel, remove the connector position assurance (CPA), disconnect the harness connector, remove the SIS mounting fasteners and remove the SIS.
By Bob
GM Specialist
01/11/2022Q: What is the installation procedure for the inflatable restraint side impact sensor?
A:
The procedure is to remove any dirt, grease, or other impurities from the mounting surface, install the SIS, install the SIS mounting fasteners, install the harness connector, install the CPA, install the center pillar trim, move the seat to the original position and enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: What should you do before replacing the inflatable restraint vehicle rollover sensor?
A:
You should disable the SIR and remove the center console.
By Bob
GM Specialist
01/11/2022See more FAQs (11)