< Back ×
My Vehicle Change Vehicle
2008 GMC Yukon
< Back to View All
Cameras & Driver Safety
- Department
- Prices
OEM (Genuine) 2008 GMC Yukon Reverse Sensor
PartNumber: 15239247
Product Specifications- Notes: Reverse Sensing System; Tahoe, Yukon, Escalade;Tahoe, Yukon, Escalade; Rear Object; Tahoe 2009-14 W/O Ltz, Yukon W/O Denali; Yukon W/Denali, Tahoe 2009-14 W/Ltz
- Other Names: Alarm, Park Sensor, Reverse Sensor, Sensor
- Item Dimensions: 4.8 x 2.3 x 1.9 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 19116085
- Part Description: 2008 GMC Yukon Reverse Sensor
Vehicle Fitment- 2008 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L ELECTRIC/FLEX, 8 Cyl 6.0 L ELECTRIC/GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
$159.65 MSRP:$251.08You Save: $91.43 (37%)
OEM (Genuine) 2008 GMC Yukon Object Sensor
PartNumber: 20823460
Product Specifications- Notes: Tahoe, Yukon, Escalade; Side Object
- Other Names: Module, Object Sensor, Sensor
- Item Dimensions: 5.6 x 4.6 x 1.4 inches
- Item Weight: 1.00 Pounds
- Fitment Type: Direct Replacement
- Replaces: 1999430, 25978649, 25910830, 20759899, 01999430
- Part Description: 2008 GMC Yukon Object Sensor
Vehicle Fitment- 2008 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 6.0 L ELECTRIC/FLEX, 8 Cyl 6.0 L ELECTRIC/GAS, 8 Cyl 6.2 L FLEX
$422.21 MSRP:$636.96You Save: $214.75 (34%)
FAQ for Parking Sensors Repair
Q: How do you install the Rear Object Sensor?
A:
You can paint the rear object sensor, ensure the paint does not exceed 6 mils, use a paint thickness gauge suitable for non-ferrous metals, insert the sensor into the housing, connect the electrical connector to the rear object sensor and install the rear bumper fascia.
By Bob
GM Specialist
02/11/2022Q: How do you remove the Rear Object Sensor?
A:
You can remove the rear bumper fascia, disconnect the electrical from the rear object sensor, lift the locking tabs on the housing and remove the rear object sensor.
By Bob
GM Specialist
02/11/2022Q: How do you replace the Rear Object Sensor Housing?
A:
You can remove the rear fascia, disconnect the sensor harness, remove the sensor from the sensor housing, sand/grind sonic weld plastic residue from the fascia, apply structural adhesive epoxy, Lord Fusor(TM) 127EZ or equivalent, to the fascia at the mating surface, use the alignment tabs, install the sensor housing to the fascia, allow adhesive to cure according to manufacturer's directions, install the sensor to the sensor housing, connect the electrical harness and install the rear fascia.
By Bob
GM Specialist
02/11/2022Q: What's the preliminary procedure for the Object Alarm Module Replacement?
A:
You should remove the front passenger bucket seat.
By Bob
GM Specialist
01/11/2022Q: What's the recommended torque for the rear object alarm module nut?
A:
The recommended torque is 2 N.m.
By Bob
GM Specialist
01/11/2022Q: How many nuts does the rear object alarm module have?
A:
The rear object alarm module has a total of 3 nuts.
By Bob
GM Specialist
01/11/2022See more FAQs (1)