< Back ×
My Vehicle Change Vehicle
2008 Chevrolet Trailblazer
< Back to View All
Air Bag
- Department
- Prices
OEM (Genuine) 2008 Chevrolet Trailblazer Side Sensor
PartNumber: 10383584
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Side Impact Sensor, Side Sensor
- Item Dimensions: 3.3 x 2.2 x 2.1 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Chevrolet Trailblazer Side Sensor
Vehicle Fitment- 2008 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
OEM (Genuine) 2008 Chevrolet Trailblazer Front Sensor
PartNumber: 10383585
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Front Impact Sensor, Front Sensor
- Item Dimensions: 3.3 x 2.2 x 2.1 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Chevrolet Trailblazer Front Sensor
Vehicle Fitment- 2008 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
FAQ for Air Bag Sensor Repair
Q: How to remove the Inflatable Restraint Vehicle Rollover Sensor?
A:
You should disable the SIR system, fold back the rear carpet, disconnect the electrical connector, and remove the nuts securing the rollover sensor to the floor panel.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the screws which retain the side impact sensor to the door?
A:
The recommended torque is 8 N.m (71 lb in).
By Bob
GM Specialist
01/11/2022Q: How to install the Inflatable Restraint Side Impact Sensor?
A:
First, you should connect the electrical connector, install the screws which retain the side impact sensor to the door and seat the water deflector to the door. Next, the door trim panel should also be installed. Finally, you should enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: How to install the Inflatable Restraint Front End Sensor?
A:
First, you should connect the sensor electrical connector and install the following parts: the connector-position assurance (CPA), the bolts retaining the discriminating sensor assembly to the frame, the headlamp wire harness, and the grille. Next, you should enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the bolts retaining the discriminating sensor assembly to the frame?
A:
The recommended torque is 8 N.m (71 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the nuts securing the rollover sensor to the floor panel?
A:
The recommended torque is 10 N.m (88 lb in).
By Bob
GM Specialist
01/11/2022Q: How to install the Inflatable Restraint Vehicle Rollover Sensor?
A:
You should install the nuts securing the rollover sensor to the floor panel and connect the electrical connectors. In addition, the rear carpet should also be installed. Next, you should enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: How to install the Inflatable Restraint Sensing and Diagnostic Module?
A:
First, you should install the SDM and connect the electrical connectors. Next, you should install the console mounting bracket and the floor console. Finally, you should enable the SIR system.
By Bob
GM Specialist
28/10/2022Q: How to disable the Negative Battery Cable?
A:
You should turn the steering wheel, place the ignition in the OFF position, and then disconnect the negative battery cable.
By Bob
GM Specialist
28/10/2022Q: How to remove the Inflatable Restraint Sensing and Diagnostic Module?
A:
First, you should disable the supplemental inflatable restraint (SIR) system. Next, you should remove the floor console and the console mounting bracket. In addition, you should disconnect the electrical connectors. Finally, the SDM should also be removed.
By Bob
GM Specialist
28/10/2022See more FAQs (7)