< Back ×
My Vehicle Change Vehicle
2008 Chevrolet Corvette
< Back to View All
Driveline, Axles & 4WD
- Department
- Prices
OEM (Genuine) 2008 Chevrolet Corvette Ring & Pinion
PartNumber: 19133225
Product Specifications- Notes: Corvette; Auto Trans; 2.56 Ratio; W/O Axle Cooling Sys.
- Other Names: Ring Pinion
- Item Dimensions: 10.6 x 9.8 x 8.9 inches
- Item Weight: 14.60 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Chevrolet Corvette Ring & Pinion
Vehicle Fitment- 2008 Chevrolet Corvette | 427 Limited Edition Z06, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
$224.04 MSRP:$290.97You Save: $66.93 (24%)OEM (Genuine) 2008 Chevrolet Corvette Ring & Pinion
PartNumber: 19133253Product Specifications- Notes: Corvette; Auto Trans; 2.56 Ratio; W/Axle Cooling Sys.
- Other Names: Ring Pinion
- Item Dimensions: 10.2 x 9.9 x 9.0 inches
- Item Weight: 15.80 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Chevrolet Corvette Ring & Pinion
Vehicle Fitment- 2008 Chevrolet Corvette | 427 Limited Edition Z06, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
OEM (Genuine) 2008 Chevrolet Corvette Gear Set, Differential Ring & Drive Pinion
PartNumber: 19133256Product Specifications- Notes: Corvette; Manual Trans; 6.2l; W/O Supercharger; W/O Axle Cooling Sys;Corvette; Manual Trans; 7.0l
- Other Names: Ring Pinion
- Item Dimensions: 9.8 x 9.7 x 8.7 inches
- Item Weight: 14.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 89059669
- Part Description: 2008 Chevrolet Corvette Gear Set, Differential Ring & Drive Pinion
Vehicle Fitment- 2008 Chevrolet Corvette | 427, 427 Limited Edition Z06, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
OEM (Genuine) 2008 Chevrolet Corvette Gear Set, Differential Ring & Drive Pinion
PartNumber: 19133257Product Specifications- Notes: Corvette; Manual Trans; 6.2l; W/O Supercharger; W/Axle Cooling Sys
- Other Names: Ring Pinion
- Item Dimensions: 10.4 x 9.9 x 9.1 inches
- Item Weight: 14.90 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Chevrolet Corvette Gear Set, Differential Ring & Drive Pinion
Vehicle Fitment- 2008 Chevrolet Corvette | Base, Grand Sport | 8 Cyl 6.2 L GAS
FAQ for Ring And Pinion Repair
Q: How to disassemble the drive pinion?
A:
You can remove the pinion nut, place the pinion housing/cage into a press, remove the pinion shaft and bearing from the housing/cage, remove the nut, bearing, spacer, and pinion shaft, install the DT-48005 and then remove the bearing from the shaft.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the pinion housing/cage bolts?
A:
The recommended torque is 30 N.m (22 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How to disassemble the ring gear and differential housing?
A:
You can remove the ring gear bolts the ring gear, the right side bearing from the differential, the differential case bolts, the left output shaft and gear from the left case, the left clutch pack from the left case, the C-clip, the gear, the right-side gears, side gear washers, and output shaft and gear, the output shaft retaining ring and output shaft and the right clutch pack from the right case.
By Bob
GM Specialist
01/11/2022Q: How to service the drive pinion shim?
A:
You should install the differential assembly, install 4 M8 x 1.25 bolts, the J 42168-1, the J 42168-9 and thumbscrew, the J 42168-11, bearings and spacer, J 42168-2, and bolt, the pinion housing/cage assembly and the pinion housing/cage bolts.
By Bob
GM Specialist
01/11/2022Q: How to assemble the drive pinion?
A:
You can install the bearing onto the pinion shaft, assemble the pinion shaft, spacer, and bearing into the housing/cage, press the bearing onto the pinion shaft, install the nut onto the pinion shaft, and then stake the areas of the nut into the notches at the end of the pinion shaft.
By Bob
GM Specialist
01/11/2022Q: How to assemble the ring gear and differential housing?
A:
You can install the right clutch pack to the right case, the right output shaft into the side gear, the right output shaft and gear, pinion gears, and washers. And then you can compress the Bellville washer and clutch pack to install the cross pin to the right differential case. You can install the gear to the left output shaft, the C-clip to the left output shaft, the left side bearing to the differential, the left clutch pack to the left case, the left output shaft and gear to the left case, the case bolts and the right side bearing to the differential.
By Bob
GM Specialist
01/11/2022Q: What special tools will I be needing when servicing the pinion gear?
A:
You will be needing a spline holder and a Getrag axle-bearing race installer.
By Bob
GM Specialist
01/11/2022Q: How to select the drive pinion shim?
A:
You can install the differential assembly, the 4 M8 x 1.25 bolts, the J 42168-1, the J 42168-9, the J 42168-11, the pinion housing/cage assembly, measure the distance between the DT-48009 and the J 42168-1, add the B2 value to the B3 value for the proper pinion housing shim thickness and then select shims equal to the calculated value.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the nut onto the pinion shaft?
A:
The recommended torque is 500 N.m (370 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the M8 x 1.25 bolts?
A:
The recommended torque is 30 N.m (22 lb-ft).
By Bob
GM Specialist
01/11/2022See more FAQs (6)