Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
Replacement and OEM Parts for 2008 Cadillac XLR Throttle Body

2008 Cadillac XLR Throttle Body

My Vehicle Change Vehicle
2008 Cadillac XLR
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
Air Filters & Intake Systems
  • Department
  • Brands
  • Prices

3 Products found

12 Q&A for Throttle Body Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM (Genuine) 2008 Cadillac XLR Throttle Body

    PartNumber: 12567376
    OEM 2008 Cadillac XLR Throttle Body - 12567376
    Product Specifications
    • Notes: Xlr; 4.4l
    • Other Names: Throttle Body
    • Item Dimensions: 7.6 x 7.0 x 6.8 inches
    • Item Weight: 1.00 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2008 Cadillac XLR Throttle Body
    More Info
    Vehicle Fitment
    • 2008 Cadillac XLR | V | 8 Cyl 4.4 L GAS
    $129.94 MSRP: $236.28
    You Save: $106.34 (46%)
  • Cardone Reman Remanufactured Throttle Body for 2008 Cadillac XLR - 67-3025

    Cardone Reman® Remanufactured Throttle Body for 2008 Cadillac XLR

    PartNumber: 67-3025
    Product Specifications
    • Notes: Relearn procedure may need to be performed upon installation of unit. Please refer to the service manual for vehicle specific instructions.
    • Gaskets Included: No
    • Housing Color/Finish: Gray/Unfinished
    • Housing Material: Aluminum
    • Idle Air Control Motor Included: No
    • Product Condition: Remanufactured
    • Throttle Body Actuation Type: Electric
    • Throttle Body Inlet Shape: Round
    • Throttle Body Outlet Shape: Round
    • Throttle Position Sensor Included: Yes
    • Part Description: 2008 Cadillac XLR Remanufactured Throttle Body
    More Info
    Vehicle Fitment
    • 2008 Cadillac XLR | All Trims | 8 Cyl 4.6L
    $94.83
  • Cardone Reman Remanufactured Throttle Body for 2008 Cadillac XLR - 67-3027

    Cardone Reman® Remanufactured Throttle Body for 2008 Cadillac XLR

    PartNumber: 67-3027
    Product Specifications
    • Notes: Relearn procedure may need to be performed upon installation of unit. Please refer to the service manual for vehicle specific instructions.
    • Gaskets Included: Yes
    • Housing Color/Finish: Gray/Unfinished
    • Housing Material: Aluminum
    • Product Condition: Remanufactured
    • Throttle Body Actuation Type: Electric
    • Throttle Body Inlet Shape: Round
    • Throttle Body Outlet Shape: Round
    • Throttle Position Sensor Included: Yes
    • Part Description: 2008 Cadillac XLR Remanufactured Throttle Body
    More Info
    Vehicle Fitment
    • 2008 Cadillac XLR | All Trims | 8 Cyl 4.4L

FAQ for Throttle Body Repair

Q: How to install the Front Wheel Bearing and Hub?
A:
You should install the hub and bearing assembly, the wheel hub mounting bolts, and the lower control arm ball stud to the steering knuckle, remove the jack stand, install the steering linkage outer tie rod ball stud to the steering knuckle, the stabilizer shaft link to the lower control arm, the brake rotor, the caliper, and the tire and wheel assembly.
By Bob
GM Specialist
02/11/2022
Q: How to test for a short to voltage in a circuit?
A:
You should set the rotary dial of the DMM to the V (DC) position, connect the positive lead of the DMM to one end of the circuit to be tested, connect the negative lead of the DMM to a good ground, and turn on the ignition and operate all accessories. If the voltage measured is greater than 1 volt, there is a short voltage in the circuit.
By Bob
GM Specialist
02/11/2022
Q: What is the recommended torque for the throttle body assembly bolt?
A:
The recommended torque is 10 N.m (89 lb in).
By Bob
GM Specialist
02/11/2022
Q: How to remove the FCI Connectors?
A:
You should slide the lever lock forward while pressing down on the lever lock release tab, disconnect the connector from the component, locate the dress cover locking tabs at the corners of the dress cover, and pull the wire out of the back of the connector.
By Bob
GM Specialist
02/11/2022
Q: How to remove the AFL/EPC Connectors?
A:
You should remove the connector from the component, locate the connector position assurance (CPA) on the top of the wire dress cover, disconnect the connector from the component, locate the dress cover locking tabs at the corners of the dress cover, and remove the nose piece by inserting a small flat-blade tool into the slots on both ends of the connector body.
By Bob
GM Specialist
02/11/2022
Q: How to inspect and clean the Throttle Body?
A:
You should remove the supercharger, and the rear supercharger inlet duct and seal, inspect the throttle body bore and the throttle body plate for deposits, and clean the throttle body bore and the throttle plate using a clean shop towel with GM top engine cleaner, P/N 1052626 or AC Delco carburetor tune-up conditioner, P/N X66P, or equivalent product, and install the rear supercharger inlet duct and seal and the supercharger.
By Bob
GM Specialist
02/11/2022
Q: How to remove the JST Connectors?
A:
You should remove the connector from the component, release the terminals by inserting the tool into the left side of the terminal release cavity as shown in the graphic, and pull the wire out of the back of the connector.
By Bob
GM Specialist
02/11/2022
Q: How to remove the Front Wheel Bearing and Hub?
A:
You should remove the tire and wheel assembly, the brake caliper and rotor, the stabilizer shaft link from the lower control arm, the wheel hub mounting bolts, and the hub and bearing assembly from the steering knuckle.
By Bob
GM Specialist
02/11/2022
Q: How to repair the AFL/EPC Connectors?
A:
You should use the appropriate terminal and follow the instructions in the J-38125.
By Bob
GM Specialist
02/11/2022
Q: What should be noted in the replacement of the Throttle Body Assembly?
A:
You should not use a cleaner that contains methyl ethyl ketone, use a carburetor cleaner to remove deposits, and always install a new throttle body gasket.
By Bob
GM Specialist
02/11/2022
See more FAQs (7)