< Back ×
My Vehicle Change Vehicle
2008 Cadillac XLR
< Back to View All
Cigarette Lighters
- Department
- Prices
OEM (Genuine) 2008 Cadillac XLR Lighter Housing
PartNumber: 25774623
Product Specifications- Item Dimensions: 2.8 x 1.5 x 1.1 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 1999477, 12450044, 01999477
- Part Description: 2008 Cadillac XLR Lighter Housing
Vehicle Fitment- 2008 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
$7.04 MSRP:$10.60You Save: $3.56 (34%)
OEM (Genuine) 2008 Cadillac XLR Receptacle Asm, Cigarette Lighter
PartNumber: 25776667
Product Specifications- Item Dimensions: 2.8 x 1.6 x 1.2 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 12450043
- Part Description: 2008 Cadillac XLR Receptacle Asm, Cigarette Lighter
Vehicle Fitment- 2008 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
$12.58 MSRP:$18.70You Save: $6.12 (33%)
OEM (Genuine) 2008 Cadillac XLR Lighter
PartNumber: 23202298
Product Specifications- Other Names: Lighter
- Item Dimensions: 2.3 x 1.4 x 1.0 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 1999433, 25617713, 10098576, 25600663, 01999433, 10060404, 11516146, 11516140
- Part Description: 2008 Cadillac XLR Lighter
Vehicle Fitment- 2008 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
FAQ for Cigarette Lighters Repair
Q: How to test for a short to ground in a circuit with a Test Lamp?
A:
You should remove the power feed (i.e. fuse, control module) from the suspect circuit, disconnect the load, connect one lead of the test lamp to battery positive voltage, and connect the other lead of the test lamp to one end of the circuit to be tested.
By Bob
GM Specialist
29/10/2022Q: How to install the Cigar Lighter Receptacle or 12-Volt Accessory Power Receptacle?
A:
You should route the connector through the retainer, align the accessory power receptacle retainer to the slot in the opening, install the retainer by pressing into place fully seated, connect the electrical connector to the receptacle, align the tabs on the receptacle to the slots in the retainer, and install the accessory power receptacle by pressing into place until fully seated, and the accessory power receptacle fuse.
By Bob
GM Specialist
29/10/2022Q: How to test for a short to ground in a circuit with a DMM?
A:
You should remove the power feed (i.e. fuse, control module) from the suspect circuit, disconnect the load, set the rotary dial of the DMM to the ohm position connect one lead of the DMM to one end of the circuit to test, connect the other lead of the DMM to a good ground.
By Bob
GM Specialist
29/10/2022Q: How to remove the Cigar Lighter Receptacle or 12-Volt Accessory Power Receptacle?
A:
You should remove the auxiliary power outlet fuse from the fuse block, and the receptacle,.
By Bob
GM Specialist
29/10/2022