< Back ×
My Vehicle Change Vehicle
2008 Cadillac XLR
< Back to View All
Air Bag
- Department
- Prices
OEM (Genuine) 2008 Cadillac XLR Side Sensor
PartNumber: 10385785
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Side Impact Sensor, Side Sensor
- Item Dimensions: 4.2 x 2.3 x 2.2 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10345690
- Part Description: 2008 Cadillac XLR Side Sensor
Vehicle Fitment- 2008 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
OEM (Genuine) 2008 Cadillac XLR Front Sensor
PartNumber: 10385762
Product Specifications- Location: Driver Side; Passenger Side
- Other Names: Front Impact Sensor, Front Sensor
- Item Dimensions: 3.3 x 3.1 x 3.1 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 10345689
- Part Description: 2008 Cadillac XLR Front Sensor
Vehicle Fitment- 2008 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
FAQ for Air Bag Sensor Repair
Q: How to remove the Inflatable Restraint Front End Sensor?
A:
You should remove the retaining bolts from the inflatable restraint front-end sensor, and the sensor from the vehicle.
By Bob
GM Specialist
01/11/2022Q: How to install the Inflatable Restraint Side Impact Sensor?
A:
You should install the sensor from the vehicle, the retaining bolts to the inflatable restraint side impact sensor, and the door trim panel.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the retaining bolts to the inflatable restraint side impact sensor?
A:
The recommended torque is 9 N.m (80 lb in).
By Bob
GM Specialist
01/11/2022Q: How to remove the Inflatable Restraint Side Impact Sensor?
A:
You should remove the door trim panel, the retaining bolts from the inflatable restraint side impact sensor, and the sensor from the vehicle.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the retaining bolts to the inflatable restraint front-end sensor?
A:
The recommended torque is 9 N.m (80 lb in).
By Bob
GM Specialist
01/11/2022Q: How to install the Inflatable Restraint Front End Sensor?
A:
You should install the sensor from the vehicle, and the retaining bolts to the inflatable restraint front-end sensor.
By Bob
GM Specialist
01/11/2022Q: How to enable the Air Bag Fuse?
A:
You should place the ignition in the off position, install the fuse(s) supplying power to the SDM, turn the ignition switch to the on position, and perform the Diagnostic System Check-Vehicle if the AIR BAG warning indicator does not operate as described.
By Bob
GM Specialist
28/10/2022Q: How to install the Inflatable Restraint Sensing and Diagnostic Module?
A:
You should remove any dirt, grease, or other impurities from the mounting surface, install the SDM horizontally to the I/P center support system, the SDM mounting fasteners, the SDM harness connector to the SDM, the CPA to the SDM harness connector, and the accessory trim plate.
By Bob
GM Specialist
28/10/2022Q: How to enable the Negative Battery Cable?
A:
You should place the ignition in the off position, connect the negative battery cable to the battery, turn the ignition switch to the on position, and perform the Diagnostic System Check-Vehicle if the AIR BAG warning indicator does not operate as described.
By Bob
GM Specialist
28/10/2022Q: How to remove the Inflatable Restraint Sensing and Diagnostic Module (SDM)?
A:
You should remove the accessory trim plate, the connector position assurance (CPA) from the SDM harness connector, the SDM mounting fasteners, and the SDM from the I/P center support system.
By Bob
GM Specialist
28/10/2022See more FAQs (8)