< Back ×
My Vehicle Change Vehicle
2008 Cadillac STS
< Back to View All
Transfer Cases
- Department
- Location
- Brands
- Prices
SKF® Front Transfer Case Output Shaft Seal for 2008 Cadillac STS
PartNumber: 18892Product Specifications- Notes: STS:
- Bore: 2.75"
- Boretite: 'No
- Outer Diameter: 2.76"
- Shaft: 1.8890"
- UPC: 085311279611
- Width: 0.52"
- Part Description: 2008 Cadillac STS Front Transfer Case Output Shaft Seal
Vehicle Fitment- 2008 Cadillac STS | All Trims | All Engines
$5.72
National® Front Transfer Case Output Shaft Seal for 2008 Cadillac STS
PartNumber: 710661Product Specifications- Notes: w/Borg-Warner 4479 Transfer Case; 1Spd; Full Time 4WD
- Inside Diameter: 47.900 mm
- Outside Diameter: 2.756"
- Sealing Material: Polyacrylate
- Thickness: 13.000 mm
- Part Description: 2008 Cadillac STS Front Transfer Case Output Shaft Seal
Vehicle Fitment- 2008 Cadillac STS | All Trims | All Engines
$6.42
FAQ for Transfer Case Output Shaft Seal Repair
Q: How to install Output Shaft Seal?
A:
The procedure is to lubricate the wheel drive shaft sealing surface of the oil seal with 75W90 synthetic axle lubricant, GM P/N 12378261 (Canadian P/N 10953455) or equivalent, install the differential output shaft seal to the J 45017, using the J 45017, install the differential output shaft seal, remove J 45017 from the differential output shaft seal, install the wheel drive shaft, inspect the fluid level, install the rear tire and wheel assembly, lower the vehicle.
By Bob
GM Specialist
01/11/2022Q: What should be noticed when installing a new O-ring in the groove on the pinion housing?
A:
You should inspect the bearing housing for nicks and burrs.
By Bob
GM Specialist
01/11/2022Q: How to remove Output Shaft Seal-Right Side?
A:
The procedure is to raise and suitably support the vehicle, remove the right front tire and wheel assembly, remove the right front wheel drive shaft, using a flat-bladed tool carefully remove the right differential output shaft seal.
By Bob
GM Specialist
01/11/2022Q: How to install Output Shaft Seal-Right Side?
A:
The procedure is to lubricate the wheel drive shaft sealing surface of the oil seal with 75W90 synthetic axle lubricant, GM P/N 12378261 (Canadian P/N 10953455) or equivalent, install the right differential output shaft seal to the J 45017, carefully install the right differential output shaft seal, remove J 45017 from the right differential output shaft seal, install the right front wheel drive shaft, inspect the fluid level, install the right front tire and wheel assembly, lower the vehicle.
By Bob
GM Specialist
01/11/2022Q: What tools are required in the replacement procedure for Output Shaft Seal-Left Side?
A:
J8092 Driver Handle, J 22912-B Split-Plate Bearing Puller, J 25070 Heat Gun, J 45012 Pinion Flange Holder, J 45019 Flange and Pinion Cage Remover, J 45017 Seal Installer, J 45124 Removal Bridge, and J 46265 Stub Shaft Seal Installer are required in the replacement procedure for Output Shaft Seal-Left Side.
By Bob
GM Specialist
01/11/2022Q: How to remove the Output Shaft Seal?
A:
The procedure is to raise and suitably support the vehicle, remove the appropriate rear tire and wheel assembly, remove the appropriate wheel drive shaft, using a flat-bladed tool remove the differential output shaft seal.
By Bob
GM Specialist
01/11/2022See more FAQs (1)