< Back ×
My Vehicle Change Vehicle
2008 Cadillac STS
< Back to View All
Steering Systems
- Department
- Prices
OEM (Genuine) 2008 Cadillac STS Sensor
PartNumber: 15231656
Product Specifications- Notes: Strg Whl Position; Sts, Sts-V; Steering Wheel Position
- Other Names: Position Sensor, Sensor
- Item Dimensions: 5.3 x 4.2 x 4.1 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaces: 26069756, 88965535
- Part Description: 2008 Cadillac STS Sensor
Vehicle Fitment- 2008 Cadillac STS | Base, Platinum, V | 6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
$112.60 MSRP:$186.40You Save: $73.80 (40%)
OEM (Genuine) 2008 Cadillac STS Sensor Asm, Steering Column Telescope Position
PartNumber: 89060602
Product Specifications- Notes: Telescopic Position; Sts, Sts-V; Telescope Position
- Other Names: Position Sensor, Sensor
- Item Dimensions: 5.7 x 4.0 x 3.7 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Cadillac STS Sensor Asm, Steering Column Telescope Position
Vehicle Fitment- 2008 Cadillac STS | Base, Platinum, V | 6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
OEM (Genuine) 2008 Cadillac STS Sensor Asm, Steering Column Tilt Wheel Position
PartNumber: 89060599
Product Specifications- Notes: Tilt Position; Sts, Sts-V; Tilt Position
- Other Names: Position Sensor, Sensor
- Item Dimensions: 5.1 x 4.2 x 4.1 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Cadillac STS Sensor Asm, Steering Column Tilt Wheel Position
Vehicle Fitment- 2008 Cadillac STS | Base, Platinum, V | 6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
FAQ for Steering Angle Sensor Repair
Q: How to remove Steering Wheel Position Sensor or Steering Shaft Lower Bearing (without JL7)?
A:
The procedure is to disable the supplemental inflatable restraint (SIR) system, remove the steering column from the vehicle, remove the boot seal, the steering shaft seal, the sensor retainer, and the sensor locator from the steering shaft, remove the steering wheel position sensor, remove the adapter and bearing assembly from the steering jacket assembly.
By Bob
GM Specialist
01/11/2022Q: What should be noticed in the installation procedure for Steering Wheel Position Sensor Centering?
A:
If reusing the existing sensor, you must align the marks on the flush rotor flange cuff before installation. The alignment mark must stay aligned until the sensor is seated into the adapter and bearing assembly. If installing a new sensor, it will come with a pin installed in the sensor. You should not remove the pin until the sensor is seated. If the new sensor did not come with a pin installed, you must reorder a new sensor.
By Bob
GM Specialist
01/11/2022Q: What should be noticed in the removal procedure for Steering Wheel Position Sensor (with JL7)?
A:
The front wheels of the vehicle must be maintained in the straight-ahead position and the steering column must be in the lock position before disconnecting the steering column or intermediate shaft.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the upper intermediate steering shaft bolt and nut?
A:
The recommended torque is 47 N.m (35 lb-ft).
By Bob
GM Specialist
01/11/2022Q: How to install Steering Wheel Position Sensor or Steering Shaft Lower Bearing (without JL7)?
A:
The procedure is to install the adapter and bearing assembly to the steering jacket assembly, install the steering wheel position sensor, the sensor locator, the sensor retainer, the steering shaft seal, and the boot seal onto the steering shaft, install the steering column into the vehicle, enable the SIR system.
By Bob
GM Specialist
01/11/2022Q: What should be noticed in the removal procedure for Steering Wheel Position Sensor Centering?
A:
You should identify the type of steering wheel position sensor from the illustrations shown before removing the sensor from the steering column. Once you have identified the steering wheel position sensor, you should follow the instructions listed in the removal procedure.
By Bob
GM Specialist
01/11/2022Q: How to center the steering angle sensor?
A:
The procedure is to align the front wheels forward, set the transmission in the park position, turn the ignition switch on, with the engine off, clear any DTCs that may be set, select Steering Angle Sensor Centering in the electronic brake control module (EBCM) Special Functions list, follow the scan tool directions to complete the centering procedure.
By Bob
GM Specialist
01/11/2022See more FAQs (2)