< Back ×
My Vehicle Change Vehicle
2008 Cadillac STS
< Back to View All
Brake Boosters & Brake Master Cylinders
- Department
- Series
- Brands
- Prices
OEM (Genuine) 2008 Cadillac STS Cylinder, Brake Master
PartNumber: 10367561
Product Specifications- Notes: W/O Active Steering Control, W/O Active Steering Control
- Other Names: Master Cylinder
- Item Dimensions: 8.2 x 6.1 x 12.5 inches
- Item Weight: 2.20 Pounds
- Part Description: 2008 Cadillac STS Cylinder, Brake Master
Vehicle Fitment- 2008 Cadillac STS | Base, Platinum, V | 6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
Centric® Premium™ Brake Master Cylinder for 2008 Cadillac STS
PartNumber: 130.62153Product Specifications- UPC: 805890436454
- Part Description: 2008 Cadillac STS Premium™ Brake Master Cylinder
Vehicle Fitment- 2008 Cadillac STS | All Trims | All Engines
Cardone Reman® Remanufactured Master Cylinder for 2008 Cadillac STS
PartNumber: 10-3161Product Specifications- Notes: Except Vehicle Stability Control;Supplied w/o Reservoir
- Bore Diameter (N): 1.00"
- E-Waste: No
- Installation Hardware Included: No
- Master Cylinder Color/Finish: Gray
- Master Cylinder Material: Aluminum
- Mounting Hole Quantity: 2
- Package Contents: Master Cylinder, Reservoir Pin Kit
- Port Quantity: 2
- Primary Port Size: 1/2 x 20
- Product Condition: Remanufactured
- Reservoir Included: No
- Secondary Port Size: 1/2 x 20
- UPC: 082617693455
- Part Description: 2008 Cadillac STS Remanufactured Master Cylinder
Vehicle Fitment- 2008 Cadillac STS | All Trims | All Engines
OEM (Genuine) 2008 Cadillac STS Cylinder Asm, Brake Master
PartNumber: 19209197
Product Specifications- Notes: W/Active Steering Control, W/Active Steering Control
- Other Names: Master Cylinder
- Item Dimensions: 9.2 x 9.1 x 8.4 inches
- Item Weight: 1.80 Pounds
- Fitment Type: Direct Replacement
- Replaces: 15267509
- Part Description: 2008 Cadillac STS Cylinder Asm, Brake Master
Vehicle Fitment- 2008 Cadillac STS | Base, Platinum, V | 6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
FAQ for Brake Master Cylinder Repair
Q: What should be noticed in the filling procedure for Master Cylinder Reservoir?
A:
When adding fluid to the brake master cylinder reservoir, you should use only Delco Supreme 11(R), GM P/N 12377967 (Canadian P/N 992667), or equivalent DOT-3 brake fluid from a clean, sealed brake fluid container. The use of any type of fluid other than the recommended type of brake fluid may cause contamination which could result in damage to the internal rubber seals and/or rubber linings of hydraulic brake system components.
By Bob
GM Specialist
01/11/2022Q: What is the removal procedure for the Master Cylinder Reservoir?
A:
The procedure is to remove the brake fluid from the master cylinder reservoir, remove the master cylinder assembly from the vehicle, drive out the secondary reservoir retaining pin, drive out the primary reservoir retaining pin, remove the master cylinder reservoir, remove the secondary master cylinder reservoir seal, remove the primary master cylinder reservoir seal.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the master cylinder primary brake pipe fitting?
A:
The recommended torque is 38 N.m (28 lb in).
By Bob
GM Specialist
01/11/2022Q: What is the assembly procedure for the Brake Master Cylinder?
A:
The procedure is to assemble the lubricated, new primary seal and retainer, and new secondary seal onto the secondary piston, install the lubricated return spring and secondary piston assembly, install the lubricated, new primary piston assembly into the cylinder bore, depress the primary piston and install the new piston retainer, install the master cylinder reservoir to the master cylinder, install the reservoir cap and diaphragm to the reservoir, and install the master cylinder to the vehicle.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the master cylinder nuts?
A:
The recommended torque is 25 N.m (18 lb-ft).
By Bob
GM Specialist
01/11/2022Q: What is the bleeding procedure for Master Cylinder Bench?
A:
The procedure is to remove the master cylinder reservoir cap and diaphragm, install suitable fittings to the master cylinder ports, install transparent hoses to the fittings installed to the master cylinder ports, then route the hoses into the master cylinder reservoir, fill the master cylinder reservoir to at least the half-way point, ensure that the ends of the transparent hoses running into the master cylinder reservoir are fully submerged in the brake fluid, depress and release the primary piston as far as it will travel, observe the flow of fluid coming from the ports, continue to depress and release the primary piston, remove the transparent hoses from the master cylinder reservoir, install the master cylinder reservoir cap and diaphragm, remove the fittings with the transparent hoses from the master cylinder ports, remove the master cylinder from the vise.
By Bob
GM Specialist
01/11/2022Q: What is the installation procedure for the Master Cylinder Reservoir?
A:
The procedure is to install the master cylinder fluid level sensor, install the secondary master cylinder reservoir seal to the master cylinder reservoir, install the primary master cylinder reservoir seal to the master cylinder reservoir, install the master cylinder reservoir, drive in the primary reservoir retaining pin, drive in the secondary reservoir retaining pin, install the master cylinder assembly.
By Bob
GM Specialist
01/11/2022Q: What is the disassembly procedure for the Brake Master Cylinder?
A:
The procedure is to remove the brake master cylinder from the vehicle, remove the reservoir cap and diaphragm from the reservoir, remove the master cylinder reservoir from the master cylinder, depress the primary piston and remove the piston retainer, remove the primary piston assembly from the cylinder bore, plug the cylinder inlet ports and the rear outlet port, discard the primary piston assembly, the piston retainer, and the seals and seal retainer from the secondary piston.
By Bob
GM Specialist
01/11/2022Q: What is the recommended torque for the master cylinder secondary brake pipe fitting?
A:
The recommended torque is 38 N.m (28 lb-ft).
By Bob
GM Specialist
01/11/2022See more FAQs (4)