< Back ×
My Vehicle Change Vehicle
2008 Cadillac SRX
< Back to View All
Cigarette Lighters
- Department
- Prices
OEM (Genuine) 2008 Cadillac SRX Lighter Housing
PartNumber: 25774623
Product Specifications- Notes: 2007-09, W/O Entertainment System, W/O Bose System; 2007-09, W/Entertainment System
- Item Dimensions: 2.8 x 1.5 x 1.1 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 1999477, 12450044, 01999477
- Part Description: 2008 Cadillac SRX Lighter Housing
Vehicle Fitment- 2008 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
$7.04 MSRP:$10.60You Save: $3.56 (34%)
OEM (Genuine) 2008 Cadillac SRX Receptacle Asm, Cigarette Lighter
PartNumber: 25776667
Product Specifications- Notes: 2007-09; 2007-09, W/O Entertainment System, W/Bose System
- Item Dimensions: 2.8 x 1.6 x 1.2 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Replaces: 12450043
- Part Description: 2008 Cadillac SRX Receptacle Asm, Cigarette Lighter
Vehicle Fitment- 2008 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
$12.58 MSRP:$18.70You Save: $6.12 (33%)
OEM (Genuine) 2008 Cadillac SRX Lighter Assembly
PartNumber: 11516141
Product Specifications- Notes: 2007-09
- Other Names: Lighter, Lighter Assembly, Tray
- Item Dimensions: 2.4 x 1.4 x 0.9 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaces: 1999434, 3534408, 14004942, 17057195, 344802, 90566933, 00344802, 01999434, 10025707, 03534408
- Part Description: 2008 Cadillac SRX Lighter Assembly
Vehicle Fitment- 2008 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
$8.97 MSRP:$12.87You Save: $3.90 (31%)
FAQ for Cigarette Lighters Repair
Q: How to remove the AFL/EPC Connectors?
A:
For connectors with a bolt in the dress cover, you should turn the bolt counterclockwise to remove the connector from the component, locate the connector position assurance (CPA) on the top of the wire dress cover, slide the CPA forward and the lever lock forward while pressing down on the lever lock release tab, disconnect the connector from the component, locate the dress cover locking tabs at the corners of the dress cover, release the locking tabs, remove the dress cover, release the rear lower half of the wiredress cover and the tabs that are holding the wiredress cover to the connector body, remove the nose piece by inserting a small flat-blade tool into the slots on both ends of the connector body, release the terminals by lifting the terminal retaining tabs on the inside of the connector and gently pull the wire out of the back of the connector.
By Bob
GM Specialist
29/10/2022Q: How to measure the voltage?
A:
You should set the rotary dial of the digital multimeter (DMM) to the V (DC) position, connect the positive lead of the DMM to one end of the circuit to be tested and the negative lead of the DMM to a good ground and turn on the ignition and operate all accessories. If the voltage measured is greater than 1 volt, there is a short voltage in the circuit.
By Bob
GM Specialist
29/10/2022Q: How to remove the Cigar Lighter Receptacle or 12-Volt Accessory Power Receptacle?
A:
You should remove the cigar lighter fuse, the cigar lighter element, and the cigar lighter housing by placing one side of the T portion of J 42059 into the tab window and the other side into the opposite tab window, pull the lighter housing straight out, remove the tool from the lighter housing, pull the housing and the retainer out of the ashtray, disconnect the electrical connector from the housing and remove the retainer from the housing.
By Bob
GM Specialist
29/10/2022Q: How to remove the 12-Volt Quarter Trim Panel Accessory Power Receptacle?
A:
You should remove the power outlet fuse, and the power outlet housing by placing one side of the T portion of J 42059 into the tab window and the other side into the opposite tab window, pull the lighter housing straight out, remove the tool from the power outlet housing, pull the housing and the retainer out of the console, disconnect the electrical connector from the housing and remove the retainer from the housing.
By Bob
GM Specialist
29/10/2022Q: How to remove the Floor Console Accessory Power Receptacle?
A:
You should remove the power outlet fuse, and the power outlet housing by placing one side of the T portion of J 42059 into the tab window and the other side into the opposite tab window, pull the lighter housing straight out, remove the tool from the power outlet housing, pull the housing and the retainer out of the console, disconnect the electrical connector from the housing and remove the retainer from the housing.
By Bob
GM Specialist
29/10/2022Q: How to remove the JST Connectors?
A:
While depressing the lock, you should remove the connector from the component, locate the two indents of the terminal position assurance (TPA) located on the bottom of the connector body, raise the TPA on both sides of the connector, use the J 38125-12A tool to release the terminals by inserting the tool into the left side of the terminal release cavity as shown in the graphic, use the tool to move the terminal release to the right with a gentle prying motion, gently pull the wire out of the back of the connector and always remember never use force when pulling a terminal out of a connector.
By Bob
GM Specialist
29/10/2022Q: What special tools do we need when we service the Auxiliary Power Outlet?
A:
The special tool you need is the J42059-cigar lighter socket remover.
By Bob
GM Specialist
29/10/2022See more FAQs (2)