Contact Us Live Chat or 1-888-220-8330
Search Bar
Search by Part Number or Keywords
  • My Garage
  • My Account
  • Cart
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Help Center
< Back ×
  • Body & Mirrors
  • Chassis & Brakes
  • Engine & Drivetrain
  • Electrical & Lighting
Login/Register My Account Track Order Help Center Contact Us
Replacement and OEM Parts for 2008 Cadillac SRX ABS Pump And Motor Assembly

2008 Cadillac SRX ABS Pump And Motor Assembly

My Vehicle Change Vehicle
2008 Cadillac SRX
Change Vehicle
Vehicle Options
We need more information about your vehicle to make a correct determination of fitment
< Back to View All
ABS & Parking Brake
  • Department
  • Prices

1 Product found

1 Q&A for Abs Pump And Motor Assembly Repair
Show Item:
  • 30
  • 60
  • 90
Sort by:
Recommended
Filter
Sort
View by
  • OEM 2008 Cadillac SRX ABS Pump Assembly Diagram - 89060233
    View Related Parts

    OEM (Genuine) 2008 Cadillac SRX ABS Pump Assembly

    PartNumber: 89060233
    OEM 2008 Cadillac SRX ABS Pump Assembly - 89060233
    Product Specifications
    • Other Names: ABS Pump Assembly, Control Valve, Modulator Valve
    • Item Dimensions: 8.4 x 6.1 x 6.1 inches
    • Item Weight: 6.40 Pounds
    • Fitment Type: Direct Replacement
    • Part Description: 2008 Cadillac SRX ABS Pump Assembly
    More Info
    Vehicle Fitment
    • 2008 Cadillac SRX | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
    $395.95 MSRP: $747.11
    You Save: $351.16 (48%)

FAQ for Abs Pump And Motor Assembly Repair

Q: How to remove the Brake Pressure Modulator Valve?
A:
You should turn off the ignition, thoroughly clean all contaminants from around the EBCM, remove the 2 master cylinder brake pipes from the BPMV, clean any brake fluid spillage from the BPMV, raise and support the vehicle, remove the air deflector shield, the wheelhouse liner, the washer solvent container bracket and the 4 wheel brake pipes from the BPMV, press the retainer on the EBCM electrical connector, rotate the EBCM connector tab forward to the unlocked position, disconnect the EBCM electrical connector from the EBCM and position out of the way and remove the front BPMV bracket nuts, the EBCM/BPMV assembly from the BPMV bracket, the 4 EBCM to BPMV screws and the EBCM from the BPMV.
By Bob
GM Specialist
28/10/2022

FAQ for Other Repair Info

Q: How to install the Parking Brake Shoe?
A:
You should install the park brake shoe assembly by grasping the shoe and spreading slightly while pulling the shoe over the actuator assembly, the Parking Brake Shoe retaining spring and the wheel bearing and hub assembly, adjust the parking brake shoe-to-drum clearance, and lower the vehicle.
Q: How to remove the Electronic Brake Control Module?
A:
You should never connect or disconnect the wiring harness connector from the EBCM with the ignition switch in the on position, then you should raise and support the vehicle, remove the air deflector shield, the right front wheelhouse liner, and the washer solvent container bracket, thoroughly clean all of the contaminants from and around the EBCM assembly, press the retainer on the EBCM electrical connector, rotate the EBCM connector tab forward to the unlocked position, disconnect the EBCM electrical connector from the EBCM and position out of the way, remove the 4 EBCM to brake pressure modulator valve (BPMV) screws, clean the surface of the EBCM/BPMV assembly and separate the EBCM from the BPMV.