< Back ×
My Vehicle Change Vehicle
2008 Cadillac Escalade ESV
< Back to View All
Timing Belts, Chains, Cams & Related Parts
- Department
- Prices
OEM (Genuine) 2008 Cadillac Escalade ESV Camshaft
PartNumber: 12612273
Product Specifications- Notes: Escalade Esv; 1st Design
- Other Names: Camshaft
- Item Dimensions: 3.4 x 3.4 x 28.3 inches
- Item Weight: 10.10 Pounds
- Fitment Type: Direct Replacement
- Replaces: 12583227
- Part Description: 2008 Cadillac Escalade ESV Camshaft
Vehicle Fitment- 2008 Cadillac Escalade ESV | Base, Platinum | 8 Cyl 6.2 L GAS
$436.08 MSRP:$721.78You Save: $285.70 (40%)
FAQ for Camshaft Repair
Q: How to install the Camshaft Position Actuator Solenoid Valve?
A:
You can install the NEW CMP actuator solenoid valve and the CMP actuator magnet.
By Bob
GM Specialist
29/10/2022Q: How to remove the Camshaft Position Actuator Solenoid Valve?
A:
You can remove the camshaft position (CMP) actuator magnet, and discard the CMP actuator solenoid valve.
By Bob
GM Specialist
29/10/2022Q: What is the recommended torque for the CMP actuator magnet bolts?
A:
The recommended torque is 12 N.m (106 lb in).
By Bob
GM Specialist
29/10/2022Q: How to install the Camshaft Position Actuator?
A:
You can compress the timing chain tensioner guide and install the EN 46330, identify the alignment hole (1) in the rear face of the CMP actuator and the locating pin on the front face of the camshaft, install the CMP actuator and timing chain, align the hole in the rear face of the CMP actuator with the locating pin on the front face of the camshaft, place a straight edge across the front face of the engine block and inspect for proper installation of the CMP actuator and timing chain, install a NEW CMP actuator solenoid valve (234), install the oil pump.
By Bob
GM Specialist
29/10/2022Q: How to remove the Camshaft Position Actuator Magnet?
A:
You can remove the water pump, the CMP actuator magnet bolts, and the magnet, and discard the CMP actuator magnet gasket.
By Bob
GM Specialist
29/10/2022Q: How to remove the Camshaft Position Actuator?
A:
You can remove the oil pump, and discard the camshaft position (CMP) actuator solenoid valve (234), loosen and separate the CMP actuator and timing chain from the camshaft. Position your fingers behind the actuator sprocket and pull the actuator away from the front of the camshaft. Never pull on the reluctor wheel when attempting to remove the actuator, remove the CMP actuator (235) and timing chain (208), and insert and secure a tie strap through the center of the actuator and over the reluctor wheel.
By Bob
GM Specialist
29/10/2022Q: What should I notice in Camshaft Removal Procedure?
A:
If camshaft replacement is required, the valve lifters must also be replaced. Ensure that the teeth of the J 42386-A mesh with the teeth of the engine flywheel. Do not turn the crankshaft assembly after the timing chain has been removed to prevent damage to the piston assemblies or the valves.
By Bob
GM Specialist
29/10/2022Q: How to install the Camshaft Position Actuator Magnet?
A:
You can install a NEW CMP actuator magnet gasket (753) onto the CMP actuator magnet, the CMP actuator magnet (752) to the front cover, the CMP actuator magnet bolts (751), and the water pump.
By Bob
GM Specialist
29/10/2022Q: What should I notice in Camshaft Installation Procedure?
A:
The gasket surface on the engine block should be clean and free of dirt and/or debris. Properly locate the CMP actuator onto the locating pin of the camshaft. The camshaft and the crankshaft sprocket alignment mark MUST be aligned properly. Do not use the CMP solenoid valve again. Install a NEW valve during assembly.
By Bob
GM Specialist
29/10/2022See more FAQs (4)