< Back ×
My Vehicle Change Vehicle
2008 Cadillac DTS
< Back to View All
Steering Systems
- Department
- Prices
OEM (Genuine) 2008 Cadillac DTS Sensor, Steering Wheel Position
PartNumber: 15231652
Product Specifications- Notes: Dts; W/Active Brake Control, W/O Telescoping Column, W/O Telescoping Column
- Other Names: Position Sensor, Sensor
- Item Dimensions: 3.8 x 3.2 x 1.8 inches
- Item Weight: 0.50 Pounds
- Fitment Type: Direct Replacement
- Replaces: 88965330, 26059045
- Part Description: 2008 Cadillac DTS Sensor, Steering Wheel Position
Vehicle Fitment- 2008 Cadillac DTS | Base, Livery, Luxury, Platinum, Premium | 8 Cyl 4.6 L GAS
$79.54 MSRP:$166.15You Save: $86.61 (53%)
OEM (Genuine) 2008 Cadillac DTS Sensor
PartNumber: 15231656
Product Specifications- Notes: Dts
- Other Names: Position Sensor, Sensor
- Item Dimensions: 5.3 x 4.2 x 4.1 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaces: 26069756, 88965535
- Part Description: 2008 Cadillac DTS Sensor
Vehicle Fitment- 2008 Cadillac DTS | Base, Livery, Luxury, Platinum, Premium | 8 Cyl 4.6 L GAS
$112.60 MSRP:$186.40You Save: $73.80 (40%)
OEM (Genuine) 2008 Cadillac DTS Sensor Asm, Steering Column Tilt Wheel Position
PartNumber: 89060599
Product Specifications- Notes: W/Column Shift; W/Console Shift; W/Active Brake Control, W/Telescoping Column
- Other Names: Position Sensor, Sensor
- Item Dimensions: 5.1 x 4.2 x 4.1 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Cadillac DTS Sensor Asm, Steering Column Tilt Wheel Position
Vehicle Fitment- 2008 Cadillac DTS | Base, Livery, Luxury, Platinum, Premium | 8 Cyl 4.6 L GAS
FAQ for Steering Angle Sensor Repair
Q: What's the preliminary procedure for replacing the Steering Wheel Position Sensor (Manual Steering Column with JL4)?
A:
The procedure is to remove the intermediate steering shaft.
By Bob
GM Specialist
01/11/2022Q: What should be done if installing a new sensor?
A:
If installing a new sensor, it will come with a pin installed in the sensor. You can't remove the pin until the sensor is seated. If the new sensor did not come with a pin installed, you must reorder a new sensor.
By Bob
GM Specialist
01/11/2022Q: What should be done if reusing the existing sensor?
A:
You must align the marks on the flush rotor flange cuff before installation. The alignment mark must stay aligned until the sensor is seated into the adapter and bearing assembly.
By Bob
GM Specialist
01/11/2022Q: What's the tip for replacing the Steering Wheel Position Sensor (Manual Steering Column with JL4)?
A:
You may disconnect any electrical connector as needed. If reusing, you should secure the old steering wheel position sensor before removing it for proper alignment upon re-installation.
By Bob
GM Specialist
01/11/2022Q: What should be done before removing the sensor from the steering column?
A:
You will need to identify the type of steering wheel position sensor from the illustrations shown before removing the sensor from the steering column.
By Bob
GM Specialist
01/11/2022