< Back ×
My Vehicle Change Vehicle
2008 Buick LaCrosse
< Back to View All
TPMS Sensors
- Department
- Brands
- Prices
OEM (Genuine) 2008 Buick LaCrosse Sensor
PartNumber: 15921013
Product Specifications- Item Dimensions: 3.6 x 1.8 x 1.4 inches
- Item Weight: 0.40 Pounds
- Fitment Type: Direct Replacement
- Replaced by: 20925924
- Part Description: 2008 Buick LaCrosse Sensor
Vehicle Fitment- 2008 Buick LaCrosse | CX, CXL, CXS, Super | 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 5.3 L GAS
$73.37 MSRP:$138.46You Save: $65.09 (48%)
Dorman® Tpms Sensor for 2008 Buick LaCrosse
PartNumber: 974-009Product Specifications- Maximum Pressure Reading: 40 PSI
- OE Part Number: 10394110, 12768826, 13586335, 15268606, 15825475, 15921013, 15922396, 20922900, 20923680, 20925924, 22853741, 22854866, 25920615, 25952370, 43130-85Z00, 43130-85Z03, 15254101, 25799331, 15123145, 15202272
- UPC: 019495230236
- Valve Color: Silver
- Valve Length: 0.50 in
- Part Description: 2008 Buick LaCrosse Tpms Sensor
Vehicle Fitment- 2008 Buick LaCrosse | All Trims | All Engines
$34.13
OEM (Genuine) 2008 Buick LaCrosse Valve Assembly Valve
PartNumber: 15853316
Product Specifications- Item Dimensions: 1.4 x 0.9 x 0.5 inches
- Item Weight: 0.30 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Buick LaCrosse Valve Assembly Valve
Vehicle Fitment- 2008 Buick LaCrosse | CX, CXL, CXS, Super | 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 5.3 L GAS
$3.95 MSRP:$5.95You Save: $2.00 (34%)
Denso® TPMS Sensor for 2008 Buick LaCrosse
PartNumber: 550-2401Product Specifications- Notes: 315 MHz, Clamp In, 62 in-lbs, 7 N.m; OE Manufactured
- Gasket or Seal Included: YES
- Monitor Type: Direct
- Mounting Hardware Included: YES
- Mounting Method: Clamp In
- Power Source: Electric
- Real Time Pressure Signal Transmission: YES
- Universal Or Specific Fit: Specific
- UPC: 042511218123
- Part Description: 2008 Buick LaCrosse TPMS Sensor
Vehicle Fitment- 2008 Buick LaCrosse | All Trims | All Engines
FAQ for TPMS Sensor Repair
Q: What is the tire pressure sensor grommet installation procedure?
A:
First, clean any dirt or debris from the grommet sealing areas. Next, install the grommet on the sensor valve stem. Install the sensor nut and position the sensor body parallel to the inside wheel surface while torquing. Tighten the nut to 7 Nm.
By Bob
GM Specialist
02/11/2022Q: When separating the tire bead from the wheel, what position should the bead-breaking fixture be in?
A:
Position the bead-breaking fixture 90 degrees from the valve stem.
By Bob
GM Specialist
02/11/2022Q: What is the recommended bolt torque for the sensor?
A:
The recommended bolt torque is 7 N.M (62 LB IN).
By Bob
GM Specialist
02/11/2022Q: What will need to be removed to access the tire pressure sensor?
A:
You will need to remove the wheel and tire assembly.
By Bob
GM Specialist
02/11/2022