Part Description: 2008 Buick Enclave Weatherstrip Asm-Front Side Door Auxiliary *Light Cashmere
More Info
Vehicle Fitment
2008 Buick Enclave | CX, CXL | 6 Cyl 3.6 L GAS
FAQ for Door Seal Repair
Q: How do you remove the Rear Side Door Weatherstrip?
A:
You need to use a flat-bladed tool to remove the weatherstrip retainers located on the weatherstrip from the locating hole in the door.
By Bob
GM Specialist
01/11/2022
Q: How do you remove the Rear Door Opening Weatherstrip?
A:
You need to remove the rear door sill plate and the weatherstrip from the pinch-weld flange.
By Bob
GM Specialist
01/11/2022
Q: How do you remove the Rear Door Upper Sealing Strip?
A:
You need to pull the sealing strip away from the door pinch-weld flange, lift upward to remove the upper portion of the sealing strip from the door pinch-weld flange, and then remove the sealing strip from the door.
By Bob
GM Specialist
01/11/2022
Q: How do you install the Rear Door Upper Sealing Strip?
A:
You need to insert the sealing strip tab into the door sheet metal, position the sealing strip to the door pinch-weld flange and apply pressure to seat the sealing strip, and then ensure that the sealing strip is fully seated against the pinch-weld flange.
By Bob
GM Specialist
01/11/2022
Q: How do you remove the Front Side Door Weatherstrip Cap?
A:
You need to lift upward on the weatherstrip to release.
By Bob
GM Specialist
01/11/2022
Q: How do you install the Front Door Opening Weatherstrip?
A:
You need to align the weatherstrip to the door opening with the bond joint positioned at the lower center of the door opening, and then install the weatherstrip to the pinch-weld flange and the front door sill plate.
By Bob
GM Specialist
01/11/2022
Q: How do you install the Rear Door Opening Weatherstrip?
A:
You need to align the weatherstrip to the door opening with the bond joint positioned at the lower center of the door opening, and then install the weatherstrip to the pinch-weld flange and the rear door sill plate.
By Bob
GM Specialist
01/11/2022
Q: How do you remove the Front Door Opening Weatherstrip?
A:
You need to remove the front door sill plate and the weatherstrip from the pinch-weld flange.
By Bob
GM Specialist
01/11/2022
Q: How do you remove the Front Side Door Weatherstrip?
A:
You need to release the weatherstrip retainer clips located around the door's edge.
By Bob
GM Specialist
01/11/2022
Q: How many retainers does the Rear Side Door Weatherstrip have?
A:
The Rear Side Door Weatherstrip has a total of 16 retainers.
By Bob
GM Specialist
01/11/2022
See more FAQs (5)
FAQ for Other Repair Info
Q: How do you remove the Transmission Control Lever Knob (Enclave)?
A:
You need to apply the parking brake, remove the floor console left extension panel, disconnect the transmission tap up/tap down switch electrical connector, and rotate the key to the run position, however, do not start the vehicle, move the transmission shift control lever rearward, insert a small flat bladed tool between the trim ring and the Shift Knob, apply careful downward pressure to the shift knob trim ring to separate the trim ring from the shift knob, and then remove the shift control knob screw from the shift control knob and the shift control knob from the shift control lever.
Q: What will need to be done before replacing the Spare Wheel Hoist?
A:
You will need to remove the tire and wheel from the Spare Tire Hoist, and then raise and support the vehicle.
Q: How do you install the Front Floor Console Rear Cup Holder?
A:
You can unsnap the front floor console rear Cup Holder from the console assembly.