< Back ×
My Vehicle Change Vehicle
2008 Buick Enclave
< Back to View All
Driveline, Axles & 4WD
- Department
- Prices
OEM (Genuine) 2008 Buick Enclave Inner Joint Assembly
PartNumber: 15855622
Product Specifications- Notes: Acadia Limited, Enclave; Left
- Location: Driver Side
- Other Names: CV Joint Kit, Inner CV Joint, Inner Joint Assembly
- Item Dimensions: 9.8 x 5.5 x 5.5 inches
- Item Weight: 1.20 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Buick Enclave Inner Joint Assembly
Vehicle Fitment- 2008 Buick Enclave | Base, Convenience, CX, CXL, Leather, Premium | 6 Cyl 3.6 L GAS
$216.89 MSRP:$345.92You Save: $129.03 (38%)OEM (Genuine) 2008 Buick Enclave Inner Joint Assembly
PartNumber: 15855632Product Specifications- Notes: Acadia Limited, Enclave; Right
- Location: Passenger Side
- Other Names: CV Joint Kit, Inner CV Joint, Inner Joint Assembly
- Item Dimensions: 5.8 x 3.6 x 3.4 inches
- Item Weight: 5.20 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Buick Enclave Inner Joint Assembly
Vehicle Fitment- 2008 Buick Enclave | Base, Convenience, CX, CXL, Leather, Premium | 6 Cyl 3.6 L GAS
$189.03 MSRP:$312.89You Save: $123.86 (40%)
OEM (Genuine) 2008 Buick Enclave Outer Joint Assembly
PartNumber: 15855621
Product Specifications- Notes: Acadia Limited, Enclave
- Location: Driver Side; Passenger Side
- Other Names: Outer CV Joint, Outer Joint Assembly
- Item Dimensions: 9.8 x 9.9 x 4.6 inches
- Item Weight: 0.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Buick Enclave Outer Joint Assembly
Vehicle Fitment- 2008 Buick Enclave | Base, Convenience, CX, CXL, Leather, Premium | 6 Cyl 3.6 L GAS
OEM (Genuine) 2008 Buick Enclave Joint Asm-Rear Wheel Drive Shaft Cv Outer
PartNumber: 15855634
Product Specifications- Notes: AWD; Enclave, Traverse
- Location: Driver Side; Passenger Side
- Other Names: Outer CV Joint, Outer Joint
- Item Dimensions: 8.2 x 3.2 x 3.1 inches
- Item Weight: 4.70 Pounds
- Fitment Type: Direct Replacement
- Part Description: 2008 Buick Enclave Joint Asm-Rear Wheel Drive Shaft Cv Outer
Vehicle Fitment- 2008 Buick Enclave | CX, CXL | 6 Cyl 3.6 L GAS
FAQ for Cv Joint Repair
Q: How do you assemble the rear wheel drive shaft outer joint and boot?
A:
You can place the new small seal clamp onto the small end of the joint seal, slide the joint seal and the small seal clamp onto the wheel drive shaft bar, position the small end of the joint seal into the joint seal groove on the wheel drive shaft bar, crimp the small seal retaining clamp, install a new barrel retaining ring to the wheel drive shaft bar, align the reference mark on the tripot spider and the wheel drive shaft bar, install the tripot spider to the wheel drive shaft bar, compress the barrel retaining ring with a flat-bladed tool, verify positive engagement of the tripot spider to the wheel drive shaft bar, place approximately half of the grease from the service kit in the wheel drive shaft outboard seal, use the remainder of the grease to repack the housing, install the trilobal tripot bushing to the housing and the spring to the tripot housing, use grease from the housing , install the guide to the spring, use grease from the housing, position the larger new seal retaining clamp on the wheel drive shaft outboard seal, slide the housing over the tripot joint spider assembly on the wheel drive shaft bar and the large diameter of the wheel drive shaft outboard seal, inspect the seal for proper shape, position the joint assembly at the proper vehicle dimension, align the wheel drive shaft outboard seal, the tripot housing and the large seal retaining clamp, latch the large seal retaining clamp, and then rotate the outer tripot housing four or five times.
By Bob
GM Specialist
01/11/2022Q: What is the disassembly procedure for the rear wheel drive shaft inner joint and boot?
A:
The procedure is to remove the small seal clamp from the wheel drive shaft bar using side cutters and discard the clamp and the large seal clamp from the tripot joint with side cutters and discard the clamp, separate the wheel drive shaft inboard seal from the trilobal tripot bushing, slide the seal away from the joint along the wheel drive shaft bar, remove the housing from the tripot joint spider and the wheel drive shaft bar, the guide from the spring and the spring from the tripot housing, mark the position of the tripot spider on the wheel drive shaft bar, carefully tap around the tripot spider face, remove the tripot spider from the wheel drive shaft bar, the barrel retaining ring from the wheel drive shaft bar and the joint seal from the wheel drive shaft bar, and then inspect the wheel drive shaft inboard seal, the tripot joint spider assembly, the housing and the trilobal tripot bushing.
By Bob
GM Specialist
01/11/2022Q: How do you assemble the rear wheel drive shaft inner joint and boot?
A:
You can place the new small seal clamp onto the small end of the joint seal, slide the joint seal and the small seal clamp onto the wheel drive shaft bar, position the small end of the joint seal into the joint seal groove on the wheel drive shaft bar, crimp the small seal retaining clamp, install a new barrel retaining ring to the wheel drive shaft bar, align the reference mark on the tripot spider and the wheel drive shaft bar, install the tripot spider to the wheel drive shaft bar, compress the barrel retaining ring with a flat-bladed tool, verify positive engagement of the tripot spider to the wheel drive shaft bar, place approximately 1/2 of the grease from the service kit in the wheel drive shaft inboard seal, use the remainder of the grease to repack the housing, install the spring to the tripot housing, use grease from the housing, install the guide to the spring, use grease from the housing, install the trilobal tripot bushing to the housing, position the larger new seal retaining clamp on the wheel drive shaft inboard seal, slide the housing over the tripot joint spider assembly on the wheel drive shaft bar and the large diameter of the wheel drive shaft inboard seal, inspect the seal for proper shape, position the joint assembly at the proper vehicle dimension, align the wheel drive shaft inboard seal, the tripot housing and the large seal retaining clamp, latch the large seal retaining clamp, and then rotate the inner tripot housing 4 or 5 times.
By Bob
GM Specialist
01/11/2022Q: What is the disassembly procedure for the rear wheel drive shaft outer joint and boot?
A:
The procedure is to remove the small seal clamp from the wheel drive shaft bar and the large seal clamp from the tripot joint with side cutters and discard the clamp, separate the wheel drive shaft outboard seal from the trilobal tripot bushing, slide the seal away from the joint along the wheel drive shaft bar, remove the housing from the tripot joint spider and the wheel drive shaft bar, mark the position of the tripot spider on the wheel drive shaft bar, carefully tap around the tripot spider face, remove the tripot spider from the wheel drive shaft bar, the barrel retaining ring from the wheel drive shaft bar and the joint seal from the wheel drive shaft bar, and then inspect the wheel drive shaft outboard seal, the tripot joint spider assembly, the housing and the trilobal tripot bushing.
By Bob
GM Specialist
01/11/2022