Notes: See installation procedure for replacing crimped or ferruled return line assemblies; Cut to fit;Hydroboost System; w/Finned Cooler; Cut to Length, 18"; See installation procedure for replacing crimped or ferruled return line assemblies; Cut to fit
End 1 Type: I.D. Molded Return Hose
End Diameter: .375 in
Length: 23.5 in
OE Part Number: 146472
UPC: 770075646655
Part Description: 2007 GMC Sierra 3500 Classic Power Steering Return Line Hose Assembly From Gear
More Info
Vehicle Fitment
2007 GMC Sierra 3500 Classic | All Trims | 8 Cyl 6.0L
2007 GMC Sierra 3500 Classic | All Trims | 8 Cyl 8.1L
Part Description: 2007 GMC Sierra 3500 Classic OE Solutions™ Power Steering Pressure Hose
More Info
Vehicle Fitment
2007 GMC Sierra 3500 Classic | All Trims | 8 Cyl 6.6L
FAQ for Power Steering Hose Repair
Q: What is the installation procedure for the power steering gear outlet pipe/hose (gas with hydroboost)?
A:
The procedure is to install the power steering gear outlet pipe to the steering gear, connect the power steering fluid cooler hose, and fill and bleed the power steering system.
By Bob
GM Specialist
02/11/2022
Q: How to properly remove the power steering gear outlet pipe/hose (gas with hydro-boost)?
A:
The proper way is to place drain pans under the vehicle, disconnect the power steering fluid cooler hose clamp and hose from the steering gear, and remove the power steering gear outlet pipe from the steering gear.
By Bob
GM Specialist
02/11/2022
Q: What is the removal procedure for the power steering gear inlet pipe/hose (gas with hydro-boost)?
A:
The procedure is to remove the power steering gear inlet hose from the power brake booster, from the power steering gear, and from the vehicle.
By Bob
GM Specialist
02/11/2022
Q: How to remove the power steering gear outlet hose?
A:
The proper way is to disconnect the power steering gear outlet hose from the power steering fluid cooler, pull the power steering gear outlet hose out of the steering gear, keep all open connections in the power steering system clean and free of debris, replace the steering gear seals if necessary, and fill and bleed the power steering system.
By Bob
GM Specialist
02/11/2022
Q: What is the installation procedure for the power steering gear inlet pipe/hose (gas with hydroboost)?
A:
The procedure is to route the power steering gear inlet hose in the same position, install the power steering gear inlet hose to the power brake booster and the power steering gear, and fill and bleed the power steering system.
By Bob
GM Specialist
02/11/2022
Q: How to properly remove the power steering gear inlet hose?
A:
The procedure is to use the remover/installer J 44586 to replace the steering gear seals if necessary, fill and bleed the power steering system, note the routing of the power steering gear inlet hose to ensure proper installation, and keep all open connections in the power steering system clean and free of debris,.
By Bob
GM Specialist
02/11/2022
Q: What is the recommended torque for the power steering gear inlet hose retaining plate bolt?
A:
The recommended torque is 12 N.m (106 lb in).
By Bob
GM Specialist
02/11/2022
Q: What should be noticed while disconnecting the power steering hose?
A:
You must not start the vehicle with any power steering gear inlet or outlet hoses disconnected. When disconnecting any power steering gear inlet or outlet hoses, you shall plug or cap all openings of components.
By Bob
GM Specialist
02/11/2022
See more FAQs (3)
FAQ for Other Repair Info
Q: What is the removal procedure for the parking brake rear cable-left side (JD9)?
A:
The procedure is to disconnect the left park brake cable from the intermediate cable equalizer bar, and the Parking Brake Cable eye from the park brake actuator lever, and remove the park brake cable assembly from the vehicle.
Q: How to install the pitman arm?
A:
You need to install the Pitman Arm onto the steering gear, a new pitman arm washer, and nut, remove the steering gear from the vise, install the steering gear, and adjust the front toe.
Q: How to properly remove the upper intermediate steering shaft?
A:
The proper way is to mark the relationship of the upper intermediate Steering Shaft to the steering column and the steering shaft coupling and remove the steering column seal, and the upper intermediate steering shaft from inside the engine compartment.