Part Description: 2007 Chevrolet Monte Carlo Front Hub
More Info
Vehicle Fitment
2007 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
Other Names: Front Hub & Bearing, Hub, Hub & Bearing
Item Dimensions: 7.1 x 6.8 x 6.8 inches
Item Weight: 7.90 Pounds
Fitment Type: Direct Replacement
Replaces: 89047803, 12413005, 12413097
Part Description: 2007 Chevrolet Monte Carlo Hub & Bearing
More Info
Vehicle Fitment
2007 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
Other Names: Hub & Bearing, Hub & Bearing Assembly
Item Dimensions: 7.3 x 7.3 x 6.3 inches
Item Weight: 8.70 Pounds
Fitment Type: Direct Replacement
Replaces: 12413099
Part Description: 2007 Chevrolet Monte Carlo Hub & Bearing
More Info
Vehicle Fitment
2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
FAQ for Wheel Bearing Repair
Q: How do you remove the wheel bearing/hub?
A:
You can remove the tires/wheels, brake rotor, ABS electrical connector, and park brake actuator.
By Omar
GM Specialist
14/03/2022
Q: What is the installation procedure for the wheel bearing/hub?
A:
The procedure is to install the park brake actuator, the wheel bearing/hub, the ABS electrical connector, and the brake rotor.
By Bob
GM Specialist
11/03/2022
Q: What is the removal procedure for the wheel bearing/Hub?
A:
The procedure is to remove the tire/wheel, disconnect the electrical connector, and remove the brake rotor, and the wheel bearing/hub.
By Omar
GM Specialist
09/03/2022
FAQ for Other Repair Info
Q: How do I install the cabin air filter?
A:
First, place the Cabin Air Filter into the filter housing next you'll need to install the water deflector cover and the air inlet grill panel. Then position the washer hose into the right air inlet grille panel clips. Install the rear hood seal and close the hood. Lastly, put the windshield wipers back in their original position.
Q: How do I install the Camshaft Position Actuator Magnet?
A:
Start with installing the Camshaft Position Actuator Magnet O-ring seal and magnet. Then install the bolts that attach the sensor. Connect the camshaft position actuator magnet sensor to the electrical connector. Lastly, install the manifold intake cover.
Q: How do I install the Drive Belt Idler Pulley?
A:
Start with attaching the required drive belt Idler Pulley, install the drive belt idler pulley bolt, and tighten it to 50 Nm (37 LB-FT). Lastly, install the drive belt.