Part Description: 2007 Chevrolet Malibu Side Sensor
More Info
Vehicle Fitment
2007 Chevrolet Malibu | Base, LS, LT, LTZ, Maxx, Maxx LS, Maxx LT, Maxx LTZ, Maxx SS, SS | 4 Cyl 2.2 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
FAQ for Air Bag Sensor Repair
Q: How do I install the Inflatable Restraint Front End Sensor?
A:
Start with installing the front end sensor to the vehicle, tighten the 2 integral bolts that retain the front end sensor to the frame front cross member top 8 Nm (71 LB IN). Connect the sensor electrical connector to the front-end sensor. Install the CPA to the sensor electrical connector and the air cleaner intake duct. Lastly, enable the SIR System.
By Omar
GM Specialist
27/03/2022
Q: How do I install the Inflatable Restraint Side Impact Sensor?
A:
Start with connecting the sensor, then place the sensor in the vehicle and install the fasteners and the door trim panel. Lastly, enable the SIR system.
By Bob
GM Specialist
27/03/2022
Q: How do I remove the Inflatable Restraint Front End Sensor?
A:
Start with disabling the SIR system. Next, remove the air cleaner intake duct and the connector position assurance from the electrical connector on the front-end sensor. Then disconnect the front-end sensor electrical connector from the front-end sensor. Remove the 2 integral bolts that retain the front-end sensor to the frame front cross member and the front-end sensor from the vehicle.
By Omar
GM Specialist
25/03/2022
Q: How do I remove the Inflatable Restraint Side Impact Sensor?
A:
First, you will need to disable to Sir System, Next remove the door trim and the fasteners attaching it to the vehicle. Lastly, disconnect the electrical connector.
By Bob
GM Specialist
25/03/2022
Q: How do you remove the inflatable restraint side impact module?
A:
You can disable the SIR system, and remove the seat back panel, the module, and the CPA.
By Omar
GM Specialist
23/03/2022
Q: What is the proper way to install the inflatable restraint sensing and diagnostic?
A:
The proper way is to install the module, the module wire harness, and the console, and enable the SIR system.
By Bob
GM Specialist
20/03/2022
Q: What is the proper way to install the inflatable restraint side impact module?
A:
The proper way is to connect the electrical connector, install the CPA, and the seat back panel, and enable the SIR system.
By Omar
GM Specialist
20/03/2022
Q: What is the proper way to install the side impact module wiring harness?
A:
The proper way is to install the new side impact module wiring harness, the retaining clips, and the side impact module.
By Omar
GM Specialist
20/03/2022
Q: What is the removal procedure for inflatable restraint sensing and diagnostic?
A:
The procedure is to remove the console, module nuts, restraint sensing, and diagnostic.
By Bob
GM Specialist
17/03/2022
Q: What is the removal procedure for the side impact module wiring harness?
A:
The procedure is to disable the SIR system, and remove the side impact module, and the clips.
By Omar
GM Specialist
17/03/2022
See more FAQs (5)
FAQ for Other Repair Info
Q: How do I install the starter motor?
A:
Place the Starter motor into the engine and attach it by installing the bolts. Then install the engine wiring harness terminal, the starter solenoid °S° terminal nut, the engine wiring harness terminal and the positive battery cable, and the positive battery cable nut to the starter solenoid. Lower the vehicle and connect the negative battery cable.
Q: What is the power mirror switch installation procedure?
A:
First, install the switch to the bezel and connect the electrical connectors to the Mirror Switch. Next, install the switch bezel to the door trim and install the door trim panel.
Q: What is the seat switch installation procedure?
A:
First, install the Power Seat Switch to the outer trim panel on the seat cushion and connect the electrical connector. Next, install the outer trim panel.