2007 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
Part Description: 2007 Chevrolet Impala Theft Deterrent Module Assembly
More Info
Vehicle Fitment
2007 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
Notes: Onstar W/O Digital Audio; Onstar W/Digital Audio
Other Names: Control Module, Module
Item Dimensions: 11.8 x 9.7 x 5.6 inches
Item Weight: 2.00 Pounds
Fitment Type: Direct Replacement
Replaces: 15257441, 25828574, 15940564
Part Description: 2007 Chevrolet Impala Module
More Info
Vehicle Fitment
2007 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
$228.35MSRP: $344.43
You Save: $116.08 (34%)
FAQ for Body Control Module Repair
Q: How many screws does the communication interface module battery have?
A:
The communication interface module battery has a total of 2 screws.
By Omar
GM Specialist
06/04/2022
Q: How many screws does the navigation receiver have?
A:
The navigation receiver has 3 screws in total.
By Omar
GM Specialist
05/04/2022
Q: What should you remove before replacing the body control module?
A:
You should remove the left closeout panel. After replacement, you should program the body control module.
By Omar
GM Specialist
29/03/2022
Q: What should you remove before replacing the communication interface module battery?
A:
You should remove the left rear compartment trim.
By Bob
GM Specialist
29/03/2022
Q: What should you remove before replacing the communication interface module?
A:
You should remove the left rear compartment trim and then configure the OnStar system after receiver replacement.
By Omar
GM Specialist
29/03/2022
Q: What should you remove during the service procedure?
A:
You should remove the OnStar(R) module.
By Bob
GM Specialist
28/03/2022
See more FAQs (1)
FAQ for Other Repair Info
Q: How do you install the starter motor?
A:
You can install the following: the Starter bolts, the engine harness terminal, and positive battery cable terminal, the starter solenoid BAT terminal nut, the torque converter covers, and the front lower air deflector panel.
Q: What should you remove before replacing the sunroof motor/actuator?
A:
You should remove the following: the carpet retainer, the sunshade, the pillar garnish molding, the upper center pillar, the rear upper quarter trim, the rear window trim, the headliner, and the Sunroof Motor/actuator.
Q: How do you install the battery current sensor?
A:
You can slide the new battery current sensor up onto the battery cable, attach the battery current sensor to the positive battery cable using tie straps and electrical tape, install the positive and negative battery cables and connect the I/P harness electrical connector to the battery current sensor.